TopDawg_43 Posted October 10, 2005 Report Share Posted October 10, 2005 It looks like I am finally going to be able to get a WB O2. I was leaning toward a AEM Uego, because it has the gauge that will fit easily into my gauge pod. I think I need to go with a 2-channel, so I can tie it into my EMS. But a 2-channel is upwads of like $500+. Is there a cheaper option out there? I really like the gauge, but I can do without it if I have to. ThanksTopDawg_43~ Link to comment Share on other sites More sharing options...
cashsaudio Posted October 10, 2005 Report Share Posted October 10, 2005 I'm not too familiar with WB o2 products just gettin new to them but i have the PLX Device r-500 which cost close to $600 for just the basic kit but i has awesome data logging that i would like to use. Link to comment Share on other sites More sharing options...
TopDawg_43 Posted October 10, 2005 Author Report Share Posted October 10, 2005 Datalogging is not an issue, because I have datalogging capibilites with my E6K. ThanksTopDawg_43~ Link to comment Share on other sites More sharing options...
substock Posted October 10, 2005 Report Share Posted October 10, 2005 http://www.innovatemotorsports.com/xcart/c...=252&page=1 Link to comment Share on other sites More sharing options...
Boosted_One Posted October 10, 2005 Report Share Posted October 10, 2005 also www.wbO2.com Link to comment Share on other sites More sharing options...
88TSI_Rob Posted October 10, 2005 Report Share Posted October 10, 2005 If you already have a NB gauge or don't need a gauge the Innovate LC1 seems like a good deal at $200. Edit: For anyone interested a group buy on Innovate wideband products is going on here:http://www.corral.net/forums/showthread.ph...223#post5252223 Link to comment Share on other sites More sharing options...
heefner Posted October 10, 2005 Report Share Posted October 10, 2005 I just got the AEM UEGO last week. Its installed but I haven't used it yet. The car isn't done. Summit has the UEGO for less than $400. I don't remember the part number but it comes with black and silver bezel, and black, silver and white gauge face. You assemble any combo you want to match gauges. It also has a programmable output you can run to your EMS. My tech II only reads a 0-1v input so I set the UEGO to the 0-1v output and I run the signal wire to that. One 02 sensor, and everyone is happy. its got data logging as well if you choose to use it. Just hook up the wire to your serial port and your done. That's my vote. Link to comment Share on other sites More sharing options...
cashsaudio Posted October 11, 2005 Report Share Posted October 11, 2005 If you already have a NB gauge or don't need a gauge the Innovate LC1 seems like a good deal at $200. Edit: For anyone interested a group buy on Innovate wideband products is going on here:http://www.corral.net/forums/showthread.ph...223#post5252223 TopDawg_43 Id go for this group buy if you like something simple. I'm into more tech info because later on i would be tuning just on the dot and make has much HP on pump gas Link to comment Share on other sites More sharing options...
TopDawg_43 Posted October 11, 2005 Author Report Share Posted October 11, 2005 TopDawg_43 Id go for this group buy if you like something simple. I'm into more tech info because later on i would be tuning just on the dot and make has much HP on pump gas Yeah I'm gonna check it out. Thanks for all the input. Link to comment Share on other sites More sharing options...
TopDawg_43 Posted October 11, 2005 Author Report Share Posted October 11, 2005 I just got the AEM UEGO last week. Its installed but I haven't used it yet. The car isn't done. Summit has the UEGO for less than $400. I don't remember the part number but it comes with black and silver bezel, and black, silver and white gauge face. You assemble any combo you want to match gauges. It also has a programmable output you can run to your EMS. My tech II only reads a 0-1v input so I set the UEGO to the 0-1v output and I run the signal wire to that. One 02 sensor, and everyone is happy. its got data logging as well if you choose to use it. Just hook up the wire to your serial port and your done. That's my vote. Is this a one channel or two channel? Link to comment Share on other sites More sharing options...
heefner Posted October 11, 2005 Report Share Posted October 11, 2005 Not sure what you mean. It reads the display of the WB02 on the gauge. Then you have one progamable channle output that can read 0-5 volts, 01 one volt, or 2-4 volts. and one output for dataloging. Link to comment Share on other sites More sharing options...
kev_rm Posted October 12, 2005 Report Share Posted October 12, 2005 is "2-channel" just something that will emulate a narrow band? If so, the plx units do that. They have a non-guage display unit unit for 259. Link to comment Share on other sites More sharing options...
TopDawg_43 Posted October 12, 2005 Author Report Share Posted October 12, 2005 After reading on and on, i believe a 2-channel is when you install to sensors. Link to comment Share on other sites More sharing options...
heefner Posted October 13, 2005 Report Share Posted October 13, 2005 After reading on and on, i believe a 2-channel is when you install to sensors. Why would you need that on a 4 cyl? Link to comment Share on other sites More sharing options...
TopDawg_43 Posted October 13, 2005 Author Report Share Posted October 13, 2005 Why would you need that on a 4 cyl? You wouldn't. For like 8V applications Check it out, i just won a really good off ebay cheap. I't used, but for $130(buy it now), i couldn't pass it up. if at all worst, I'll have to buy a new sensor. They are like $40 I believe. Link to comment Share on other sites More sharing options...
Truth Posted October 19, 2005 Report Share Posted October 19, 2005 3sx has an impressive wideband for sale right now. Link to comment Share on other sites More sharing options...
Recommended Posts