-
Posts
376 -
Joined
-
Last visited
-
Days Won
1
Content Type
Profiles
Forums
Calendar
Gallery
Everything posted by 860QuestTuner
-
Pic?
-
whats the media look like?, is there a baffle? I'm interested,I started to make one and never finished.
-
To be clear is this is a bare block? I understand all the machining done.
-
Custom apparel & accessories
860QuestTuner replied to StallionProject86's topic in Group Purchase Info
Filled in profile pic, the i heart my fatty is fine. -
Custom apparel & accessories
860QuestTuner replied to StallionProject86's topic in Group Purchase Info
Can u do a pic of the car and have it say i love my fatty under it? -
still availible? i'm in ct
-
Can you post the part# of the 3-wire 02
-
I'm down for the complete njv head. I have Paypal. What's the word on the engine?
-
Pics of console? Any Pics? It sucks that another car is being parted out.
-
Need Center console, guage cluster top with switches or without,idle step motor ,temp swithch for egr, and a more peices I need to check on.
-
Condition of engine? how much without trans?
-
How's the engine?, I need bad.
-
No it is not a bolt on, but you could make something work by moding it heavily. I know personally I own a evo and a quest
-
what's up, i'm interested in the scheider springs,valves and headlight switch. maybe a idle motor for 88/89. I have paypal and in the 06040. How much? Thanks
-
interested in engine with pistons ect. I need one bad, but I am in CT so I will have to figure something out. I assume the block just needs assembly and the bolt on parts and it's good to go? Is it bored over? Thanks
-
Still Availible?
-
Did you happen to do a compression test to verify engine is rebuilt and making compression?
-
Don't need the tranny unless it comes with engine.
-
interested in whole engine. i live in CT, can pick up
-
Possible 4" Intercooler Group Purchase
860QuestTuner replied to brianpaul98's topic in Group Purchase Info
counting the days, What about the bolting it in stock location situation and having that pipe cross over to original pipe location that was factory on the right side of the intercooler? -
Where are these engines located?
-
MK! Mookeeh Intercooler?
860QuestTuner replied to hachi_destroyer's topic in Advanced Virtual Mechanic
I don't beleive it is a factory fit. The width is much bigger than stock. The product is good though. Basicly the same as most aftermarket but not china crap. -
I would like to see the car I live in Manchester ,CT. I would be willing to help you remove some parts for sale if you have anything I need. Let Me Know.
-
performance clutch question
860QuestTuner replied to StreetVelocity's topic in Advanced Virtual Mechanic
There is a comp clutch set up in the group buy section that is top notch.I just bought one a few months ago.They are in stage 2or4 and Great Quality. Other people have liked act,fidanza,exedy(dakini). I had some good luck with centerforce daul friction that I had for awhile. -
I did the same thing in my 89 manual and replaced the boost solnoid with a led to detect knock. My understanding with the manual is that when starting up to 3 or 4k the light would be on indicating low boost and then go out indicating high boost. If the light came back on after 4k then the igniter would be pulling timing and turning on the solnoid to run low boost due to knock . I thought the auto car would allow full boost from start until it detected knock and activated the solnoid to run low boost. There is some posts from like 6 years ago on this subject and some different approuches of the same mod. I will have to check my manual to confirm. When I did this mod years ago I thought the same thing that i was knocking. I even went to the extent of puting a chasis ear mic next to the knock sensor to see if i could hear a little ping.