importwarrior Posted February 15, 2013 Report Share Posted February 15, 2013 (edited) what about a surge tank in the enginebay with a new fuel pump.have the fuel pressure regulator drain back in to the surge tank.use the old fuel pump to keep surge tank full. then the surge tank overflow back to the original gas tank..... Edited February 15, 2013 by importwarrior Quote Link to comment Share on other sites More sharing options...
button Posted February 15, 2013 Author Report Share Posted February 15, 2013 (edited) It was a mechanical pump. //edit: I almost forgot I converted it to electricalBut I'll put that on my "to consider" list.Thanks dude! Edited February 15, 2013 by button Quote Link to comment Share on other sites More sharing options...
button Posted April 11, 2013 Author Report Share Posted April 11, 2013 (edited) what if I changed my mind a little bit...http://www.ilostmymind.com/upload/img_20130316_153927800x600.jpgMaybe this can be just as fun.I slapped a hydraulic turbo cam/rockers in, and it looks like my flange will serve as an adapta-plate.now I am strongly considering megasquirt for this with a 36-1 crank trigger wheel, still distributor, but tbi.I figure I have a minute or two to screw around.Bought some seats today.93 corolla seats to be exact. I have not test fit them, but they look like they will fit in well.http://www.ilostmymind.com/upload/img_20130317_165701_copy1.jpghttp://www.ilostmymind.com/upload/img_20130317_165723_copy1.jpgSo, I whipped these up.http://www.ilostmymind.com/upload/img_20130407_162731_800x600.jpgI painted them black, then installed them.http://www.ilostmymind.com/upload/img_20130407_180400_800x600.jpgSo far so good.I'll make the second set once I get more materials.http://www.ilostmymind.com/upload/img_20130408_230903_800x600.jpgI have to order some couplers, But I think I am going to run my ic piping this way.My flat parts guy said he should have my 36-1 trigger wheel and mount cut before the weekend. http://www.ilostmymind.com/upload/img_20130410_003940_800x600.jpgI stuffed a couple 1050cc FIC injectors in the conquest TBI and stacked some nuts and a washer as spacers.Not as fancy as some machined billet, but quick, easy, cheap, and effective.Warm weather seems to help a lot.http://www.ilostmymind.com/upload/img_20130410_205314_800x600.jpgHere is my custom cut 36-1 trigger wheel for the g5xb early crank pully.I suppose It could be welded onto a rubber inserted one as well. I'll probably get more cut in time. Edited April 23, 2013 by button Quote Link to comment Share on other sites More sharing options...
importwarrior Posted April 11, 2013 Report Share Posted April 11, 2013 how much power does that make?the seats lok quite comfy. amazing how much stuff you have done over the years. Quote Link to comment Share on other sites More sharing options...
IntercooledFlatty Posted April 11, 2013 Report Share Posted April 11, 2013 this roxx Quote Link to comment Share on other sites More sharing options...
button Posted April 13, 2013 Author Report Share Posted April 13, 2013 http://www.ilostmymind.com/upload/img_20130413_015911_800x600.jpgI had to do it.These are so much more comfortable and easier to install.iw, on the desktop dyno, It's estimated 200hp, 160ft/lbs on 15psi. And thanks for following my projects over the years.Olive8, thank you. Quote Link to comment Share on other sites More sharing options...
Technology Posted April 14, 2013 Report Share Posted April 14, 2013 That half-moon breather tube on the front of the head is one of the coolest parts I've ever seen. Quote Link to comment Share on other sites More sharing options...
3sdsmer Posted April 14, 2013 Report Share Posted April 14, 2013 what happened with the 4g set up? Quote Link to comment Share on other sites More sharing options...
button Posted April 22, 2013 Author Report Share Posted April 22, 2013 what happened with the 4g set up?I decided that for my requirements for this car, the 2.0 sohc will work just fine once it is boosted and throttle body injected.Technology, It's a stock part on the colt/arrow/lancer 1.6/1.8/2.0 motors I believe. Definitely the ones with jet valves, I'm not sure about the pre-78 without jet valves. Quote Link to comment Share on other sites More sharing options...
button Posted April 28, 2013 Author Report Share Posted April 28, 2013 http://www.ilostmymind.com/upload/img_20130428_170837_800x600.jpg36-1 trigger wheel is mounted.Silicone couplers are on the way.Megasquirt is built.I need to get crackin on that wiring. Quote Link to comment Share on other sites More sharing options...
importwarrior Posted April 28, 2013 Report Share Posted April 28, 2013 would that dizzy fit the quest?where did you get the 36-1 wheel from? Quote Link to comment Share on other sites More sharing options...
button Posted April 29, 2013 Author Report Share Posted April 29, 2013 The dizzy looks to be the same as a quests, except points style. I had my flat parts guy cut me the 36-1 wheel and sensor holder. I drew it up in autocad.I opted for the crank trigger because there is about 10° of "slop" between the crank and cam with the chain. Quote Link to comment Share on other sites More sharing options...
button Posted May 6, 2013 Author Report Share Posted May 6, 2013 Now we are talking.http://www.ilostmymind.com/upload/img_20130505_132837_copy1.jpghttp://www.ilostmymind.com/upload/img_20130505_132852_copy1.jpgBut, hindsight being 20/20, I need to put the radiator in before the IC due to the location of the trans cooler and the bolts go in from the IC side.I need to figure out if I am going to put the AIT in the intake pipe, or the IC pipe. Quote Link to comment Share on other sites More sharing options...
Technology Posted May 6, 2013 Report Share Posted May 6, 2013 Is that the only fuel pump? Quote Link to comment Share on other sites More sharing options...
button Posted May 6, 2013 Author Report Share Posted May 6, 2013 yes. questions/concerns? Quote Link to comment Share on other sites More sharing options...
Technology Posted May 6, 2013 Report Share Posted May 6, 2013 If it works, then no! Quote Link to comment Share on other sites More sharing options...
button Posted May 6, 2013 Author Report Share Posted May 6, 2013 (edited) Yeah, it works.shes a genuine walbro so it should all be good.that is all.btw, doesn't the fender roller look like its superimposed. Edited June 8, 2013 by button Quote Link to comment Share on other sites More sharing options...
tsiconquest88 Posted May 9, 2013 Report Share Posted May 9, 2013 Lovin it man!! On a side note is that Carb the same for an 88 mighty Max 2.0?? I would buy it off ya. I can't find a good deal on new or used Weber Carb swap and my Volvo upgrades sucks my extra fun-ds lol Quote Link to comment Share on other sites More sharing options...
button Posted May 10, 2013 Author Report Share Posted May 10, 2013 (edited) maybe, I don't know. Pay for shipping and pp fees, and you can have it. Might even have a gasket set for it.I also got a new camera... well, phone, whatever.http://www.ilostmymind.com/upload/imag0001.jpgAlso, I put the hood on. I broke 3 of the four bolts that held it on, but they drilled out really easy, and I just had to clean the threads up. Edited May 10, 2013 by button Quote Link to comment Share on other sites More sharing options...
button Posted May 12, 2013 Author Report Share Posted May 12, 2013 Oil cooler.Looks like it should be able to handle the job.http://www.ilostmymind.com/upload/imag0003_copy2_copy1.jpghttp://www.ilostmymind.com/upload/imag0010_copy1.jpgI don't have a front plate, but you get the idea. Quote Link to comment Share on other sites More sharing options...
importwarrior Posted May 12, 2013 Report Share Posted May 12, 2013 Looking good!!!!! Quote Link to comment Share on other sites More sharing options...
button Posted May 31, 2013 Author Report Share Posted May 31, 2013 It runs.http://ilostmymind.com/upload/imag0033.jpgAnd, here's a shot for Technology of the breather deal.http://ilostmymind.com/upload/imag0032.jpghttp://ilostmymind.com/upload/imag0031.jpg And, my hooker aerochamberhttp://ilostmymind.com/upload/imag0037.jpg and a video. Quote Link to comment Share on other sites More sharing options...
importwarrior Posted June 1, 2013 Report Share Posted June 1, 2013 Awesome that thing is purring like a kitten.got to love megasquirt. great work! Quote Link to comment Share on other sites More sharing options...
natedog_37 Posted June 4, 2013 Report Share Posted June 4, 2013 Where is Niles Michigan. I need to see this thing.... it is clean for a Michigan car... Quote Link to comment Share on other sites More sharing options...
importwarrior Posted June 4, 2013 Report Share Posted June 4, 2013 (edited) looks to be 163 miles 2 hours 50 min west of you on I80 Edited June 5, 2013 by importwarrior 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.