bflann
Members-
Posts
121 -
Joined
-
Last visited
-
Days Won
1
Content Type
Profiles
Forums
Calendar
Gallery
Everything posted by bflann
-
Is there a time frame for a batch release
-
I am with quik , do luck double 6 ' s give the shp's a run for the money and the do luck ' s r serious money
-
MPI general guide lines
bflann replied to Bag-O-Chips's topic in MPI/Standalone Trials and Tribulations
thanks again gentlemen I found the zachman how to on ausiestarion board, he basically shorted across the tach resistor and used a 12v square wave tach output from haltech unit which is the way I will be going since I have to pull the cluster to replace bust guage. On a side note scotty I have a ? for u kinda off topic, I saw in a thread were u bought a tep stage 3 build from guy in mexico I think, for like 2G, was that a true deal and what did u do with that motor, was the quality of build good,because I am basically getting that from tep u can pm me the answer if u want -
I need maroon center console w/ lid & seatbelt guides, rear speaker panels w/ seatbelt guides and a-pillars driver & passenger side TIA
-
place a nut on the bolt and cut against the nut and then back it off the bolt repairing the cut end of bolt
-
I would like one also
-
I would like one if they are still available
-
MPI general guide lines
bflann replied to Bag-O-Chips's topic in MPI/Standalone Trials and Tribulations
Thanks for the info Scott , I will go with MAP, get IAT sensor , going distributorless , eliminating knock sensor , but with going distributorless will I still be able to use the stock rpm guage, it seems to work with distributor , so how can I get a signal / pulse back to rpm guage. I am going with the smart coil to eliminate the need for ignition module -
MPI general guide lines
bflann replied to Bag-O-Chips's topic in MPI/Standalone Trials and Tribulations
Which stand-alone system allows you to eliminate ecu completely and still perform all of the functions of the stock units or should Sal ' s be used as systems that control fuel & ignition only while stock controls other functions ? I ask this because I would like to replace my stock ecu with a haltech ps 1000 and use smart coils for ignition. So is anyone here operating a stand-alone that controls all of the stock ecu functions -
I am looking for maroon rear/backseat shoulder seatbelt guides, driver side visor, center console cover and radio console
-
Do you have the rear/backseat shoulder seatbelt guides
-
2front and 2rear bumpers for sale calif car
bflann replied to markhansenconquest's topic in Parts for sale
paypal sent -
2front and 2rear bumpers for sale calif car
bflann replied to markhansenconquest's topic in Parts for sale
Can you send pics of front bumper metal core to bflann@comcast.net -
Pm 'd u
- 25 replies
-
- radio trim
- taillight trim
-
(and 1 more)
Tagged with:
-
I also need the rear/back seat shoulder seatbelt guides from 89 starquest
-
Need front bumper metal frame for 89 quest, shipped to 32277
-
pm'd u, interested in front bumper frame
- 25 replies
-
- radio trim
- taillight trim
-
(and 1 more)
Tagged with:
-
parting out one 87 starion and one 89 conquest
bflann replied to pineapple1961's topic in Parts for sale
I pm'd u for some pics of the 89 quest -
pm'd u
- 25 replies
-
- radio trim
- taillight trim
-
(and 1 more)
Tagged with:
-
do u have the backseat shoulder seatbelt guides
-
I want the accelerator pedal and the cruise control cable shipping to 32277
- 25 replies
-
- radio trim
- taillight trim
-
(and 1 more)
Tagged with:
-
do u still have the cruise control actuator and cable
-
CXracing Starion intercooler
bflann replied to Calquest's topic in eBay/ Craiglist notices and alerts
Where are u advertising the tbi hard pipe kits Sotty -
Is the front bumper frame still available and if so what will it cost to ship to 32277
- 15 replies
-
Do you have cruise control actuator and cable