Turbo_84_Starion

You have a known good distributor with vacuum advance? Need the whole unit, mine took a crap on me.

Thank you, it was M10x1.25 60mm bolts for the starter. I still don't know what size bolt for the alternator but some trial and error will have to do.

What's the starter bolt thread pitch? Also, what length bolts do I use with the A/C delete alternator bracket?

I'm definitely planning on it. My work can do without me for a few days.

Just called today and spoke to Jerry. He was very helpful in setting up my order. The last two sets that were gonna be ready for September were sold out this morning, so mine will be ready around the first of October. SO EXCITED!!

For that amount of money, I would expect camber plates front and rear. That said, I will be down for a set next month if still available. Awesome job getting this going man HUGE props.

PM Sent for turbo

I was looking at this product that POR-15 offers: http://www.por15.com/FUEL-TANK-REPAIR-KIT/productinfo/FTRK/

Aw, closest place is in California... dumb hippies gettin the good stuff. Indiana, that's why I mentioned the POR-15. I just don't know if I can get the rust out of places where I can't see it; how will I know I got all the rust? I don't want to have to change fuel filters, lines, and pump every 3 months cause of rust, you know?

^Is that a reversed throttle body?^

Ive just checked around here in Vancouver. Can you recommend a place?

I could use a kit like Por 15 to remove the rust, but I'm concerned I won't do the job right. Am I better off taking the tank to a mac's radiator shop to have it cleaned and sealed? The price is what concerns me the most. Por 15 only costs $73.25, whereas Mac's quoted me $225 and 7-10 days to get the job done. From what I've seen, it only takes a couple days to do the job yourself. Opinions?

Thanks Indiana. So I need to return the whole cylinder, rod and all, and make sure I get the non intercooled version?

Can anyone tell me what plugs into where? I think the one I labeled 5 grounds to the intake where the egr valve bolts on. BONUS: Can I use the old rod with the new cylinder? Or did I get the wrong year/intercooled one?

Header panels any different between the years? I need one... $30 plus shipping sound good?

NO! lol I need a small emblem like that. The front emblem on my car is broken and faded...

I don't have one, but 3SX has one... It's quite expensive however http://www.3sx.com/store/comersus_viewItem.asp?idProduct=1463

Sweet! Do these work for flatties as well?

Just got this email:

Payment sent for clutch/flywheel.

http://www.autoblog.com/2010/04/21/ken-blocks-gymkhana-fiesta-revealed/

It was tons of fun; we got so much closer than the paying spectators did... we didn't have to pay because we signed up to be volunteers to help with controls/timing, which ended up being "hey, go block off this road so no idiot decides to go for groceries during the race" and cracking a few brews lol

All in all it was pretty sick... Dave Mirra rolled his car on Fur Mountain, then Ken Block rolled his 800 HP AWD Ford Fiesta into Dave Mirra... Both crews were fine but the cars weren't. And guess what kind of cars dominated the standings?? MITSUBISHI Lancers and Evo's of course!! ACP won first in a NOS Evo X I believe. Anyway here's the link to my album on Facebook: http://www.facebook.com/album.php?aid=214449&id=662145578&l=0e776baa01

I bet that stage 4 grabs hard... lol I never like six pucks for daily driving

Do I still have dibs on the flywheel? If so, I'll be sending payment Friday when I get my paycheck.