Laodicea

I need the aluminum spacer between firewall and booster...

If someone could give measurements of a poly bushing. I think it would be a good start. I don't want to take mine apart either to make these.

I need 4 of the 5.5" straight tie rod adjuster that is on the driver side steering link. 75081 zip.

This is the exact replacement bulb...you can get them on Ebay for like $3 shipped for two. I bought two last week. #2162 Miniature Automotive Light Bulb Lamp

X2

You will have lots of fun beating out your tunnel to fit the tranny....

Get a bar and plate....I know of a guy who puts out over 1100hp in his supra with a low cost bar and plate ebay intercooler.

Bingo!

http://i156.photobucket.com/albums/t18/gr8white1/Steering/IMAG0573.jpg http://i156.photobucket.com/albums/t18/gr8white1/Steering/IMAG0574.jpg http://i156.photobucket.com/albums/t18/gr8white1/Steering/IMAG0576.jpg http://i156.photobucket.com/albums/t18/gr8white1/Steering/IMAG0564.jpg http://i156.photobucket.com/albums/t18/gr8white1/Steering/IMAG0579.jpg Was leaking no matter what crush washer/sealant I used....so I fixed that with the tig and some -6 AN. http://i156.photobucket.com/albums/t18/gr8white1/Steering/IMAG0587_zps16814211.jpg http://i156.photobucket.com/albums/t18/gr8white1/Steering/IMAG0588_zpsf9622769.jpg

I was shocked at the price...I can buy two widebody rollers before I would buy two window rollers for that...LOL

They are simple Z shaped brackets I made by bending some thick straight stud tie in's you get at Home Depot or Lowes etc. You may get a good idea of what they are by the two pics below...that is all the pics I have of them. I didn't have to drill any holes on the bottom of the car the way I placed in on. It uses some existing bolt holes. I did take off the factory frame tie down brackets from the bottom of the car.

Well I had my computer hooked up to an older 65" 1080p with the RBG cables for years and I was just tired of dragging the screen over for anything I wanted to watch and then try to stretch back from the computer to try and see if I had the mouse on the fullscreen button. Then when I wanted to pause I had to get up and do the stretch/make sure mouse was on the correct part of the screen to pause/play again. The Roku allowed me to watch all the same channels/netflix and more without going to the computer with the handy remote. Just saying...you might get tired of doing that too after 6 years like I did. Roku is not a dish...it runs through your internet connection...thus getting internet channels.

Ok guys this has been almost a year since any updates. LOL I need to see some rear widening...I got some 18x12 -44 in mind begging for me to buy and put on the rears.

LOL that second video looks like the track is wet all the way down. Good run.

A little late answering...do it. A/c is hard to keep...Do a N/A 2jz and single turbo it....I get 11 miles a gallon E85.

I finally broke down and got a 1989 Vol 2 Electrical Conquest manual....and low and behold the relay locations for the defogger and anti theft horn relays have been swapped....it sure helps to know where the relay is that you are trying to test....the 88 manual is backwards. http://i156.photobucket.com/albums/t18/gr8white1/IMAG0598_zps53ba34bc.jpg I had the relay hidden under the fender ever since i went mpi thinking it was really the theft horn relay...so yeah..about 4 years ago my defogger quit working because it was corroding under the fender out of sight. http://i156.photobucket.com/albums/t18/gr8white1/IMAG0596_zps4b197e4c.jpg http://i156.photobucket.com/albums/t18/gr8white1/IMAG0597_zps947944df.jpg http://i156.photobucket.com/albums/t18/gr8white1/IMAG0603_zps5d9c1b7f.jpg This is the only relay on the car I can find like this....see how the prongs are offset...two smaller then two larger slightly further apart? I cannot seem to find the right relay when I try and look it up online....anyone know where to get one or send me one..??

Just go get a Roku and watch internet stuff on the TV.

Anyone have a set of the black Stedebani they wanna get rid of?? Black poly rear suspension bushings. Or is there a source on these. I DONT want the red ones.

Dang and I really need one....I'll take two please!!! http://www.ebay.com/itm/NEW-83-93-Chrysler-Conquest-Dodge-Mitsubishi-Plymouth-Window-Motor-Lift-FL-RL-/230886500587?pt=Motors_Car_Truck_Parts_Accessories&hash=item35c1e868eb&vxp=mtr

Get the link back up...I got work to do.

Did you ever sell these?

It is easy to remove....easy as pie

Ok with all that stuff up above I did. I also...am making it a bolt on 240 rack. Because with a 2JZ under the hood you have no room for the brackets to weld on to the k-member because of the oil pan clearance...it has to sit lower....also there will be no tilt to the brackets making the pinion shaft stab straight instead of leaning back towards the firewall. Meh it will still work. I should have it all in by friday and I will update on how it turns out. http://i156.photobucket.com/albums/t18/gr8white1/Steering/IMAG0559.jpg http://i156.photobucket.com/albums/t18/gr8white1/Steering/IMAG0556.jpg http://i156.photobucket.com/albums/t18/gr8white1/Steering/IMAG0557.jpg http://i156.photobucket.com/albums/t18/gr8white1/Steering/IMAG0563.jpg

Hey If it don't go and comes off ...CHROME IT!