jayfressh

I have a known working Conquest 1987 manual transmission. Asking $125 pick up in Brunswick, Ohio. Located 20mi south of Cleveland, 20mi North of Akron. Reply, PM, or call 216-374-2268

Deal, PM me a address to paypal.

I am in need of a hood latch, the side that is bolted to the hood. Please reply with price shipped to Ohio 44212.

$25 shipped I can send you a stock Mitsubishi wastegate actuator off a 14B.

I have the cable uncertain if I have the plastic pull lever in the car. Let me check and get back to you, but I for sure need the hood latch.

Looking to buy a hood latch, I need the latch that is bolted to the hood. Please reply with price shipped to 44212 Justin Kresty.

Looking for the engine mount nut size, I tried a few different metric sizes 10x1.50, 10x1.25 etc... Possibly the stud top is just a bit banged up from swapping motors. Hoping I just have the wrong size, if not there will be 2 cross threaded studs after I jam these 1.50s on, and I'll just replace the whole mount next time around.

What size AN how much? What do you need, I have more parts than what is listed DSM and StarQuest?

14B/G and or 16G waste gate actuator - $22 shipped 1g Eclipse/Talon/Laser blow off valve , crushed held 25psi strong with no leaks - $25 shipped L87-3 & L72-2 580cc injectors, from a 87-89 Conquest $22pc shipped Will trade as partial payment for aftermarket fuel pump, fuel pressure guage, oil cooler, 1g DSM AN fuel rail adapter.

I have been coating over 5 years. I am not offering any services as I do not have time at the moment, I rarely get to work on my car being that I am always coating something for a friend. Wanting very badly to drive my car this summer, I have become selfish and made that my priority. I'd more than happy to answer any questions you might have, and I have some pictures of my work in a build thread on here.

Cool red looks amazing, paint your interior trim pieces to match....

I am a powder coater, and to answer the OP's question, yes. You can coat a block and timing cover. There is high temp powder that can be used, but I don't think it would be necessary for a block, and timing cover. It's debatable if a cylinder head would dissipate heat better, ceramic coated, polished, powder coated, or left as a raw cast/machined.

Is there a preferred method of routing the throttle cable on 4g63 swaps? I've looked for pics but haven't found much short of one guy who rotated the throttle body 90* to get it on the outside of the intake. Are most swappers just cutting out the bend or bending it straight? Is anyone shortening the cable length? Thank you.

Like painting your diff red added 30hp too?

1st choice red, second choice whatever is cheapest. I'm just south of Cleveland, so Dad it looks like your about 1hr away, I'll give you a ring tomorrow morning. Thank you.

Looking for hood in North East Ohio, Cleveland/Akron area. PM or text/call 216-374-2268

very amused, where and how much are those Jap louvers?

Injectors $20pc shipped. Upgraded injectors, came off running car. L72-2 injector primary 580cc 87-89, top is chipped, does not leak, clip seats perfect to injector. $18 shipped http://i141.photobucket.com/albums/r66/jayfressh/IMGP0059.jpg L87-3 injector primary 580cc 87-89 no chips, no leaks $20 shipped http://i141.photobucket.com/albums/r66/jayfressh/IMGP0057.jpg

1g turbo MAF harness side plug $15 shipped. Great for hard wiring 1g MAF or using 2G maf converter cable.

Looks good, tell her to get off the car lol.

Finally got around to coating and bolting a few things together, takes me a bit since most the things I coat are for customers and I'm always putting off or selling my build parts Stock 4g63 valve cover shaved and coated Candy purple with Hyundai oil cap Bill Hincher fabbed intake manifold powder coated to match fuel rail, black fine textured. RC 550's installed for start up http://i141.photobucket.com/albums/r66/jayfressh/P1130436.jpg http://i141.photobucket.com/albums/r66/jayfressh/P1130438.jpg http://i141.photobucket.com/albums/r66/jayfressh/P1130434.jpg Compressor housing is off, I had it clocked totally wrong, gives me chance to redo the powder coat in a new color looking back that gold sucked donkey dill HX35 with 12cm housing, EVOIII manifold with adapter plate holding it all together Hincher bellhousing mated to W56, new release bearing, waiting on a clutch disc. http://i141.photobucket.com/albums/r66/jayfressh/P1130439.jpg

Bump it's hot stay cool with this awesome part.

Climate control display and controller, matching units from same car. The climate display has a broken tab,I used a washer and it mounted just fine. Asking $35 shipped

Bwahaha what a bag of d****! "Risky Devils" that was in a 90's video game Tokyo Extreme.

Suspect claims there, if it isn't re-sleaved or a 1.8 to begin with. I would think a 1.6 to 2.0 bore would leave the already bogusly thin walled cylinder walls egg shell thin?