wrngwae Posted January 16, 2012 Report Share Posted January 16, 2012 i have a turbosmart megasonic BOV like his. i got it 2nd hand without a proper flange.http://www.evasivemotorsports.com/Merchant2/graphics/00000001/206.jpgand i have 2.5 inch innercooler piping. but im not too sure if this will fit. http://www.ebay.com/itm/2-5-Type-H-RFL-BOV-XS-weld-Flange-Adapter-IC-Pipe-/260934786162?pt=Motors_Car_Truck_Parts_Accessories&vxp=mtr&hash=item3cc0ecdc72 i know this one will but it is way too long. and dont want to cut it. http://www.treadstoneperformance.com/product.phtml?p=1392&cat_key=177&prodname=Turbosmart+Blow+Off+Valve+Adapter any one have any sugestions? input? anthing that can help Thanks! Link to comment Share on other sites More sharing options...
FLATBROKE313 Posted January 16, 2012 Report Share Posted January 16, 2012 Yes sir it will work fine Link to comment Share on other sites More sharing options...
wrngwae Posted January 16, 2012 Author Report Share Posted January 16, 2012 Yes sir it will work finewhich one??? the ebay or treadstone? Link to comment Share on other sites More sharing options...
Side-Swipe Posted January 16, 2012 Report Share Posted January 16, 2012 (edited) Measure the gap on the turbosmart. I looked it up and they are 38mm usually on forums but just to be sure. The type H I believe is different. Because when searching for 38mm and Type H together the top hits are adapters. Edited January 16, 2012 by Side-Swipe Link to comment Share on other sites More sharing options...
Side-Swipe Posted January 16, 2012 Report Share Posted January 16, 2012 (edited) Ok I went on a hunt, here is the manual for your blow off:http://www.xspeed.co...G-BOV-003MS.pdf Which mentions this part number that needs to be welded on:Part # FG-ADA2-WA38 And this site that has it as an adapter to be welded on:http://www.onlineper...ndex=Turbosmart And this is what it looks like:http://www.onlineper...ada2-wa38-s.jpg So you need a flange like this minus the evo adapter:http://www.ebay.com/...=item5891c86788 And then here treadstone has 38mm to raceport(the original pipe you posted) adaptor:http://www.treadstoneperformance.com/product.phtml?p=420&cat_key=177&prodname=Turbosmart+Universal+Blow+Off+Valve+Adapters Edited January 16, 2012 by Side-Swipe Link to comment Share on other sites More sharing options...
wrngwae Posted January 16, 2012 Author Report Share Posted January 16, 2012 Thanks Nazar Good info! Link to comment Share on other sites More sharing options...
wrngwae Posted January 16, 2012 Author Report Share Posted January 16, 2012 (edited) what a bout this one? http://www.ebay.com/...=item5891cb4274 i could just weld it in right? Edited January 16, 2012 by wrngwae Link to comment Share on other sites More sharing options...
Side-Swipe Posted January 17, 2012 Report Share Posted January 17, 2012 what a bout this one? http://www.ebay.com/...=item5891cb4274 i could just weld it in right? I say just be safe and go with this one, if anything you can get many pipes to bolt this on to as well, very popular flange. http://www.ebay.com/itm/38mm-1-5-Type-RS-blow-off-Adapter-Lancer-EVO-1-8-/380402952072?pt=Motors_Car_Truck_Parts_Accessories&vxp=mtr&hash=item5891c86788 Link to comment Share on other sites More sharing options...
Side-Swipe Posted January 18, 2012 Report Share Posted January 18, 2012 This one is probably easier to weld on: http://www.ebay.com/itm/38mm-1-5-SSQV-blow-off-Adapter-Lancer-EVO-1-8-/260935819759?pt=Motors_Car_Truck_Parts_Accessories&vxp=mtr&hash=item3cc0fca1ef Link to comment Share on other sites More sharing options...
psu_Crash Posted January 18, 2012 Report Share Posted January 18, 2012 Just grab a 1.5" tube and weld it on your IC piping. Looks like that BOV has set screws and an O-ring. Slide it on over the 1.5 pipe and tighten. Link to comment Share on other sites More sharing options...
wrngwae Posted January 18, 2012 Author Report Share Posted January 18, 2012 (edited) thanks crash,,, but i got that flange and a pipe it bolts to for a decent price. hope i can SQUEEEZE it in,,,,, i have a guy tha can tig weld and he said that he might have an issue with the thickness of my piping and welding.... so i went the e-bay route... hope it dosent bite me in the butt! Edited January 18, 2012 by wrngwae Link to comment Share on other sites More sharing options...
psu_Crash Posted January 21, 2012 Report Share Posted January 21, 2012 If you know someone with a TIG there is no reason he shouldn't be able to weld your IC pipes. Heck I have welded bungs to mine and I am an extreme amateur with a TIG. You should be just fine Link to comment Share on other sites More sharing options...
Recommended Posts