Instaboost Posted February 13, 2011 Report Share Posted February 13, 2011 (edited) 1988 Silver Chrysler Conquest TSi **Car Needs To Be Dyno Tuned** Price is $8000 o.b.o Will remove parts to lower the price for the buyer. Not parting out the car so don't ask! Engine: SDS EM-4E Stand Alone Fuel Management SDS Controller Mounted In The Glovebox *DM Metal Turbo Inlet Pipe w/ K&N Filter 18G *DM Turbo with Mirror Polished Eclipse Housing Steel Braided Turbo Coolant Line w/ AN Fittings Steel Braided Turbo Oil Line Magna Multiport Intake Manifold Racetronix 65lb Injectors Ford 65mm Throttle Body *DM Race Cylinder Head "Details Are Below" ARP Head Studs Krank Vent System Steel Braided Fuel Line w/ AN Fittings New Fuel Filter External 38mm External Wastegate w/ Factory Manifold 3 Inch *DM Exhaust - No Converters Hooker Aero Chamber Muffler *DM Intercooler Hardpipes *DM Bar and Plate 4 Inch Thick Intercooler *DM Black Silicone Connectors Balanced Internals w/ Balance Shaft Eliminator Walbro Fuel Pump MSD 6A Ignition MSD 8920 Tach Adapter MSD Blaster 2 Coil Accel 8.8 Spark Plug Wires Rotella T5 Oil Fram Tough Guard Oil Filter Turbo-XS Type H Blow Off Valve Trunk Mounted Optima Battery "Homeless2b" Delphi 110amp Alternator Bracket Delphi 110 Amp Alternator Drivetrain/Suspension:5 Speed KYB Struts Suspension Technqiues Front and Rear Sway Bar Polyurethane Sway Bar Bushings Polyurethane Endlink Bushings Stedebani Master Polyurethane Bushing Kit Stedebani Black Polyurethane Transmission Mount Stedebani Black Polyurethane Rear Differential Mount ACT Clutch Steel Braided Clutch Line Axxis Metal Master Brake Pads Slotted Rear Rotors Steel Braided Brake Lines ABS Delete S&M Rear Strut Bar S&M Rare 3 Point Front Strut Bar Interior: Black Leather 88 Seats 89 One Touch Drivers Side Window Switch 88 Mint Hvac Panel Factory Radio A-pillar Dual Gauge Pod with Autometer Boost and Fuel Pressure Wideband Gauge Mounted In The Console Stock Radio Alpine Door Speakers Pioneer Rev Series Rear Speakers Momo Black Steering Wheel Stedebani Short Shifter Greddy Profec Boost Controller Oem Black Conquest Floor Mats Exterior: Polished Shp Wheels / 75% Tread Mint Oem 3 Piece Metal Louvers w/ All Hardware 89 One Piece Airdam Aftermarket Sunroof H4 Diamond Headlights *DM Race Head Details: Built from a Starion or Conquest TSi Spain MARNAL non-jet head along with an O-Ring job, *DM Innovative Kustom Performance Cam and Titanium Retainers, 120lb springs, Stainless Steel 1mm O/S valves, Porsche 911 Swivel Adjusters and Special Spring Retainers, Manual Adjusters this is proven to enhance your air flow beyond your wildest dreams. Valve guides removed and cut down in length and top circumference for low profile special valve stem seals, spring shoulder base diameter reduced for dual springs. Head helped produce 337-Whp on TBI and 569-Whp on MPI. NOTE I have had three of these heads built for me. One head, just like this was used to create 337 rwhp on my car. Chris Vipers old tbi car. 500 rwhp plus was made with this set up on another members car. Bigger turbo The car as it sits now has no dyno tune so I cannot say what hp its making. I am looking forward to changing out the head, turbo, and exc mani. Will be installing a tep 18g w/ stock wastegate. Head will be a marnal njv lol with roller rockers hd springs. The numbers programed in the sds are more suited to this rather than the race head. Will make these changes if she doesnt sell in a couple weeks. Thanks This was an auto car, it has the larger tunnel for a T56 swap 6 speed. Has been converted to a conquest 5 speed. http://i1222.photobucket.com/albums/dd494/papermaker1995/StarQuest/1988%20Silver%20MPI/1.jpg http://i1222.photobucket.com/albums/dd494/papermaker1995/StarQuest/1988%20Silver%20MPI/2.jpg http://i1222.photobucket.com/albums/dd494/papermaker1995/StarQuest/1988%20Silver%20MPI/3.jpg http://i1222.photobucket.com/albums/dd494/papermaker1995/StarQuest/1988%20Silver%20MPI/4.jpg http://i1222.photobucket.com/albums/dd494/papermaker1995/StarQuest/1988%20Silver%20MPI/5.jpg http://i1222.photobucket.com/albums/dd494/papermaker1995/StarQuest/1988%20Silver%20MPI/6.jpg http://i1222.photobucket.com/albums/dd494/papermaker1995/StarQuest/1988%20Silver%20MPI/7.jpg http://i1222.photobucket.com/albums/dd494/papermaker1995/StarQuest/1988%20Silver%20MPI/8.jpg http://i1222.photobucket.com/albums/dd494/papermaker1995/StarQuest/1988%20Silver%20MPI/9.jpg http://i1222.photobucket.com/albums/dd494/papermaker1995/StarQuest/1988%20Silver%20MPI/10.jpg http://i1222.photobucket.com/albums/dd494/papermaker1995/StarQuest/1988%20Silver%20MPI/11.jpg http://i1222.photobucket.com/albums/dd494/papermaker1995/StarQuest/1988%20Silver%20MPI/12.jpg http://i1222.photobucket.com/albums/dd494/papermaker1995/StarQuest/1988%20Silver%20MPI/13.jpg http://i1222.photobucket.com/albums/dd494/papermaker1995/StarQuest/1988%20Silver%20MPI/14.jpg http://i1222.photobucket.com/albums/dd494/papermaker1995/StarQuest/1988%20Silver%20MPI/15.jpg http://i1222.photobucket.com/albums/dd494/papermaker1995/StarQuest/1988%20Silver%20MPI/16.jpg Edited February 14, 2011 by Instaboost Quote Link to comment Share on other sites More sharing options...
FijiPhil Posted February 13, 2011 Report Share Posted February 13, 2011 I rode in this car before it had the worked head and had a smaller turbo. This thing will fly! Someone will get a nice ride. Quote Link to comment Share on other sites More sharing options...
NotStock88 Posted February 13, 2011 Report Share Posted February 13, 2011 (edited) So the motor was not rebuilt, just balanced and b/s eliminated? Head helped produce 337-Whp on TBI and 569-Whp on MPI. So this is the numbers it made without a professional dyno tune? Edited February 13, 2011 by NotStock88 Quote Link to comment Share on other sites More sharing options...
S.M.B Posted February 13, 2011 Report Share Posted February 13, 2011 why selling Quote Link to comment Share on other sites More sharing options...
Blue Posted February 13, 2011 Report Share Posted February 13, 2011 If only I had that kind of money. Lol Hope it sells man, excellent buy. Quote Link to comment Share on other sites More sharing options...
toofast Posted February 13, 2011 Report Share Posted February 13, 2011 Wish i had the cash good luck with the sale Quote Link to comment Share on other sites More sharing options...
Instaboost Posted February 13, 2011 Author Report Share Posted February 13, 2011 why selling I own 5 rite now. Going to put some of this money in another project. Quote Link to comment Share on other sites More sharing options...
Instaboost Posted February 13, 2011 Author Report Share Posted February 13, 2011 So the motor was not rebuilt, just balanced and b/s eliminated? So this is the numbers it made without a professional dyno tune? LIsten. These dyno numbers were done @ DC Performance, with the same spec head and cam. Yes on a dyno lol. 337 rwhp was made on my tbi car, the old Chris Viper car. The 569 rwhp dyno pull was on Questtsi s Car. Same port polish job. Thanks for asking. Quote Link to comment Share on other sites More sharing options...
DMC-4OOEX Posted February 14, 2011 Report Share Posted February 14, 2011 BEAUTIFUL car! Super clean and looks so nicely done. The things I would do to own this.. haha. Good luck with the sale. Quote Link to comment Share on other sites More sharing options...
Instaboost Posted February 14, 2011 Author Report Share Posted February 14, 2011 BEAUTIFUL car! Super clean and looks so nicely done. The things I would do to own this.. haha. Good luck with the sale. lol Thanks. I get some looks. Doesn't exactly sound like a 4 banger. Quote Link to comment Share on other sites More sharing options...
Skullzaflare Posted February 14, 2011 Report Share Posted February 14, 2011 lol Thanks. I get some looks. Doesn't exactly sound like a 4 banger.is this the car CJ told me about? i do like it a lot, but i cant afford it lol Quote Link to comment Share on other sites More sharing options...
backslider Posted February 14, 2011 Report Share Posted February 14, 2011 Sorry I have been unable to contact you or your friend this weekend. It was a hectic weekend as I am just finishing moving, so no internet at the moment just my phone. Plus I had my kids this weekend. Expect contact from me tomorrow. Max That car is beautiful. Quote Link to comment Share on other sites More sharing options...
Trajays Posted February 14, 2011 Report Share Posted February 14, 2011 WOW!! WOW!! WOW!! that is what I dream about when I think of what mine will look like.... of course, after I buy one and then put some cash into it. Quote Link to comment Share on other sites More sharing options...
NotStock88 Posted February 14, 2011 Report Share Posted February 14, 2011 (edited) just want to clarify these things; It needs tuned and has no dyno numbers currently? the bottom end was or was not rebuilt? Thanks - and great looking car!! Edited February 14, 2011 by NotStock88 Quote Link to comment Share on other sites More sharing options...
Instaboost Posted February 14, 2011 Author Report Share Posted February 14, 2011 so the motor was not rebuilt and the HP numbers you posted are from others people cars? You really should clarify this in your post, its kind of mis-leading. First post has been edited. Thank you Notstock88 Will likely start changing some parts. race head18g turbowastegate Price will be adjusted if and once i do this. Thanks everyone!!! Quote Link to comment Share on other sites More sharing options...
rockvilleash1976 Posted February 15, 2011 Report Share Posted February 15, 2011 I owned this car for a few years. I never had the time to finish the car but this guys has done an awesome job with it. He is a good guy and has no reason to mislead anyone. Every car he touches he makes better than the way he found it. If you are interested in this car just talk to the guy and you will tell he is an honest and straight forward guy. The car is worth the money and Charlie is a good guy to deal with. Quote Link to comment Share on other sites More sharing options...
backslider Posted February 15, 2011 Report Share Posted February 15, 2011 Excuse my lack of search but I am limited on internet access and have been out of the Mitsu game for several years..... But can one run a A/C system using the Magna intake? Quote Link to comment Share on other sites More sharing options...
SOTTY Posted February 15, 2011 Report Share Posted February 15, 2011 Excuse my lack of search but I am limited on internet access and have been out of the Mitsu game for several years..... But can one run a A/C system using the Magna intake?Yes Quote Link to comment Share on other sites More sharing options...
88maroon Posted February 15, 2011 Report Share Posted February 15, 2011 man if i only had the money to spend on another car i would. so close to me too. car looks great btw Quote Link to comment Share on other sites More sharing options...
Instaboost Posted February 20, 2011 Author Report Share Posted February 20, 2011 (edited) Hey members. I have started to remove the turbo,louvers, and head. The head going on is a marnal with hd springs and roller rockers. The turbo will be a TEP 18G, using the stock mani and wastegate. Price for her will be more marketable, closer to 6k. The SDS tune is way more suited and drivable with this head and set up. Thanks everyone!!! Edited February 20, 2011 by Instaboost Quote Link to comment Share on other sites More sharing options...
Instaboost Posted February 24, 2011 Author Report Share Posted February 24, 2011 Car is being returned to stock as we speak. SOME parts will be sold to fund another project. Thanks Charlie Quote Link to comment Share on other sites More sharing options...
killa26 Posted February 27, 2011 Report Share Posted February 27, 2011 up for charlie i just bought my 89 from him. really knows his is stuff and is a man of his word Quote Link to comment Share on other sites More sharing options...
StarquestRescue Posted February 27, 2011 Report Share Posted February 27, 2011 I am interested in the mpi inter cooler hard pipe set up. I already have the intercooler. Quote Link to comment Share on other sites More sharing options...
Instaboost Posted February 27, 2011 Author Report Share Posted February 27, 2011 I am interested in the mpi inter cooler hard pipe set up. I already have the intercooler. They are going in another mpi car I am building, or they would be all yours. ThanksCharlie Quote Link to comment Share on other sites More sharing options...
themitsubishifreak Posted March 1, 2011 Report Share Posted March 1, 2011 wow sorry to see this go back to stock. nice build and good looking. glws. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.