bls77red

I looked up them.there are a couple models of interface. The one you listed was for diesel alternator to tach interface. I'm going to call Dakota and find the one they suggest. Thanks for chiming in. I almost scrapped the idea.and was heading toward building a new cluster

So the Dakota digital will work with the msd box? I was wanting to keep the stock tach functional. Are you running it to the white wire on the original harness?

Hi everyone . I have been putting miles on my fresh motor her. I have a 302 lunati roller cam,aluminum heads,studded bottom and to end.airgap take,holley 4150 carb,msd dist,6al coil. t5 wc transmission. its be a blast to drive . im still tryint get my tach to work . I have msd 8920 tach adaper... anyone using stock tach in their swaps?

has anyone used the stock tachometer with their engine swap. say one with a msd 6al and msd distributer and coil? im trying to with the msd tach adapter. and having no luck

Looking for a decent used air dam.I am in illinois .paypal ready.

I have a few questions.but can't start topics. Hummm

yes I already am have a pressure regulator with a return port. any suggestions on powering the stock pump then? can I hook up my stock coil wire leads to my new coil? just trying to figure this out before my new motor goes in

Gotcha.I am doing a motor swap and curious what sends signal back when cars running?not going to use fi.but a.regulater and carburetor motor.thanks

sorry to jump on this thread with a question. but I am new to the quest and my fuel pump is stock. when does the fuel pump kick on and off? like key on, or cranking? thanks

I have the new speedo cable for mustang. And I am using my quest speedo. The cable does not.secure to the back of the speedo housing. It slips on fine.just no way to secure it to stock speedo housing.any ideas

please delete

please delete .went to the crusher

thanks everyone for interest.alot parts found homes. thanks vbrad.. and please delete

Alternator,1"spacers with shallow mounting lugs,2_7" wheels 1_8"wheel are the only items I have left .

Sorry I have problems loading pics on here. I can text or email some. Belly pan is metal

set of 86' seat belts .complete set front and rear $45 shipped . belly pan $45 shipped. wiper cowls $30 shipped .hood latch,brake,clutch reservoirs,lower black bolsters,upper rear trim panels make offer (3) 8 '' wheels $35 each , (2) 7' wheels $25 each. 1''hub eccentric spacers with shallow spacers to install make offer, new 87' stock replace clutch kit $45shipped,newer alternator $35 shipped. pics or info 217-891-8678 in illinois

Clutch is a stock replacement for 87 year. It maybe has 100 miles on it. Exedy brand with pilot,throwout,pressure plate,friction disc. $45 shipped

Panel is gone.I have the wiper cowls.but the have one crack.and not.the best shape

Vbrad I have the full seat belts for the 86. And a good drivers pillar trim also

hi .. I have the parts your looking for. 86' header panel and grill. 217-891-8678 for pics

yes I do have the control valve on throttle body. I have pics a text or call 217-891-8678 thanks

its a stock replacement clutch kit.it is like new for 87' .

what I have is a good standard bore block that will need bored. standard crank that needs turned. rod bearing failure. block plate,oil p an dip stick. they have been sonic cleaned! cylinder head that is good n cracks between valves. a barely used exxedy clutch kit... with pilot and throw out bearing. fairly new alternator , intake manifold, throttle body minus injector. message me or text 217-891-8678 or pics and info. all parts make offer. located in central Illinois

I have 2 16x8 wheels.and they have centers. message me for pics

I checked head between valves and its good. I have good clean oil pan,pickup tube,dipstick,powersteering pump,new alternator,exxedy clutch kit,barely used complete disc pate pilot throw out,block plate,crank,block, timing cover , distributor .