Doc Wylee
-
Posts
42 -
Joined
-
Last visited
Content Type
Profiles
Forums
Calendar
Gallery
Posts posted by Doc Wylee
-
-
-
The rust is Moderate I'd say considering the age. I purchased it whole and not running, It had been sitting for several years from an individual and nursed it back to life.
Heres a link to all the imperfections I could find.. in addition the paint on the roof the clear coat is hazing and a little on the hood but with wax it isnt visible unless you look directly at it
http://smg.photobucket.com/user/PortalKidd/library/Conquest%20Tsi
Again im willing to work with almost all offers... Mechanically this car is sound.. the body needs work.
-
Thanks, just trying to put it to use as I no longer have time for it.
-
Anyone? Offers?
-
-
payment sent for wiper cover.
-
PM sent on driver side side wiper cover.
-
How much for the driver side wiper cover shipped to 43230?
-
Is the wiper cover in tact and if so how much?
-
swapped from a perfectly running car ..unmodified. 90$ shipped
http://img.photobucket.com/albums/v60/PortalKidd/IMAG1333.jpg
http://img.photobucket.com/albums/v60/PortalKidd/IMAG1334.jpg
-
Ahh thanks Texasquest
-
EDIT: Retracting dib on headgasket !
-
Thanks I have the TEP one was just wondering if there was one Ive seen with the adjust ment in the center trust was the brand i thought.
-
I cant see does it have the adjustment in the center?
-
Have an interest in the headgasket if no one has purchased it
-
fenders? possibly shipped to 43230?
-
if you part the car how bout those fenders? both driverside and passenger side shipped to 43230?
-
bump
-
Anyone have one of these they're looking to get rid of? I checked and its a 4-6 week wait for fabrication and Im hardly trying to wait that long if I dont have to.
Feel Free to PM me or reply to this thread if you know the whereabouts of one.
-
Is this bar still available?
-
I recently installed this valve... Its great however I ran into some annoyances during initial use because it was prematurely venting at mid throttle. Synapse suggested I try a variation of different port configurations "A>B>A+B" and then attempt to adjust the preload screw. I ended up settling on running port A and tightening preload screw half way in from its shipped state. Now it holds great. I love this product although situating it was a pain due to its size and position of the flange on the OVCP.
Im running a 12/14b turbo and it will blow off at idle but no where near the sound it has under load.. god damned thing sounds like a bus air brake. BUT.. no more rich condition across the board from leaky valve
Oh running the stock MAF i definitely advise going with the Anti Stall kit .. and after install removing battery lead to reset computer. (had a greddy type S knock off on that was sucking hella bad at idle)
http://img.photobucket.com/albums/v60/PortalKidd/544462_410299109007743_262949314_n.jpg
-
how much for the whole thing?
-
Looking for the Thermastat Housing and the sensor that plugs in right below it If still available. Shipped to 43230 PM me I have paypal on standby.
Thanks
-
TWM M1Abrams (Gun Metal, Pattern 1)
http://img.photobucket.com/albums/v60/PortalKidd/IMAG0614.jpg
http://img.photobucket.com/albums/v60/PortalKidd/IMAG0654.jpg
Yea It costs a lot but i like the way it looks. and feels.
http://www.twmshiftknobs.com/shiftknobs/shiftknobs_shop1.php?gearknob=Mitsubishi%20Starion&twmonly=
87 Conquest in Columbus Ohio
in Cars for sale
Posted · Edited by Doc Wylee