questian

Has anyone seen my old girl on the road any where? building another one for a good friend of mine and i'am forced to remember all the s*** i used to do to her,but if you see her let a fella know

Well.. just want to say thanks to everyone that asked about my quest " nuff appreciation" to all. SOLD........SOLD......SOLD

HERE ARE A FEW CLIPS OF MY '87 QUEST FOR SALE http://www.youtube.com/user/madquest001?feature=mhee

Very nice car i have the same year same color

BUY IT....BUY IT....... if not i'm gona need a bigger house

Motor has 9.5 k, tranny has 57 k the rest of the car has 117k as far as hp i would be lying if i list a number because i street/high way tune the car using software and wideband i was thinking about getting it on a dyno but never got around to it but honestly i dont care about that number because i know what power feels like,this thing will spin the tires in 1st,2nd3rd and keep going sideways if you let it.IT will do this every time you pull away from a dead stop hard so the power is up there. A buyer of the car wiil not disappointed.

Away from a few very small door dings on the right side and the front panel has some tiny chips from highway driving which no one can escape plus i have not seen one that didn't have that,trust me guys thie is a beautiful car,its a head turner i get alot of good compliments everytime i drive this car people always approached me about it and asked to take pics of it as if it was some type of exotic car. Hey guys thanks looking and asking about the car

Hey sorry about the term pump i tend to call supercharger/turbos pumps because that is what they do,they pump air. About the sale of this car i'm giving the laptop with the Lc1 software/megasquirt and so on and alot of extra parts with the sale of this machine

I am selling my quest to anyone that wants a nice turn key mutiport get in an drive car needs nothing ,i'm only selling because i have too many toys i have taken this thing up to 140 many times with no problems 40 over weisco piston arp hardware top an bottom custom mulltiport 850cc injectors balanced crank fuel/ignition 4 bar map sensor megasquirt expanded stock radiator 88 transmission with flywhl act 6 puck sprung with HD PLT HKS EXAUST from pump to bumper 20g pump mech cam HD valve spring none jet valve head 3 upgraded electric cooling fans 4" custom intercooler LC1 WIdeband mp boost guage 18" wheels/tires walbro fuel pump and other stuff i cant remember right now,more pics on craigslist broward

Sorry man i'm not too knowledgable on the ign pro but if its configure like mega then you should make sure the LEDS that relates to bank 1 and 2 flash when you try to start it if they do then you are getting signal from the VR sensor so proceed by checking your software configuration wheel settings/spark settings and all that good stuff you can also put a volt/ohms meter on your spark A and B outputs to verify if signal is getting to the coil pack.

What method are you using to fire the plugs inter or exter and which ms are you using? i may be able to help if you using 1v3.0 with internal hardware.

Not bad.... not bad at all.I did the 6 puck spring hub disc and i like it,very soft going in gear,very quiet and aggressive at the same time it's like going from analog to digital signal meaning its on or it's off i guess the three short pucks and three taller pucks have alot to do with the quick to launch nature of it,so i'm hoping it will keep the 2.6 connected to the rear 8teens for a while.

That sounds just like the the problem i had with mine,every time that i would get on it in forth gear and then back off the trottle that noise would come alive,swapped out the disk and the noise went bye bye dont know if noise was cause by the solid hub or it being a 6 puck,so that is why i'm doing some research on the sprung hub 6 puck before i buy it.Thanks again guys

Thanks for the feedback man but I'm more concern about drivetrain noise like during decel because I had a puck setup before when I had smaller fly wheel on it, man that thing was noizeee......

Dont forget to install the isolators between the trans and heatsink