monte383sbc Posted July 25, 2009 Report Share Posted July 25, 2009 (edited) This is a Autronic smc standalone ecu removed from a 1988 conquest starion , this set up came off a MPI set up '' multi port fuel injection '' engine. this is not the stock ignition/ fuel controll computer or harness, this is a one of a kind set up for the g54b engine it has a costom crank trigger made to mate with your stock harmonic balancer and and the trigger mounts to the timming cover, holes will need to be drilled in the balancer to mount the wheel, the stock distributer is also modded for a pick up to conroll the system, there is a little dent on the computer cover and it did not hurt the computer internals at all this came off a running car, also coolant temp sensor and air intake sensor is included, a MSD box is also included the DIGITAL DIS 4 harness and pigtail comes with it too, The autronic harness is labeled on each wire to tell your were it goes so you dont have to go threw a hassel figuring out were each wire goes, this standalone computer have a very neat system to it, it has a autotune mode so it tunes as you are driving, this system is a very easy system to tune with and you can make some serious horespower, and you dont have to be a rocket scientist to tune with it, comes with a USB tuning cable to plug right in to your laptop or computer, you can download softwere from <a href="http://www.autronic.com.au/" target="_blank">http://www.autronic.com.au/</a> its very easy. comes with printed manual to show you how to hook it on and diagnois problems, this standalone ecu originally goes for $3000.00 with just the computer and harness, so buy it now for half the price, $1300.00 can be used on other vehicles too but with out the crank trigger, ive seen EVOs,talons,eclipses,supras,240,starions,conquests alot of imports with turbo and superchargers run this system, so if thats a car that you have this system is for you, thanks for looking These systems can cater for the requirements of virtuallyany spark ignition engine, including the following: - High output supercharged or turbocharged engines, with either multi point and/orcentre point injection.Rotary (Wankle) and two stroke engines.Engines having uneven firing sequences such as 2 and 4 cylinder ‘V’ configuration motorcycle engines and V6 motor vehicle engines.IMPORTANT: - Please note that this product is intended for high performance motor sport application and compliance with statutory regulations when used on public roads cannot be guaranteed.FEATURESEight injector drivers for full sequential operation on engines up to eight cylinders. May be set for ‘semi-sequential’ operation on engines having more than eight cylinders, eg: - 12 cylinder engine using 6 groups of 2 cylinders.All injector types catered for (0.9 ohm to 16-ohm coil resistance). Specify unit fitted with optional high current injector drivers for 0.9 ohm or twin injector applications.User choice of manifold absolute pressure or throttle position as engine load input. Internal absolute pressure sensor for simplified installation 0 to 200Kpa (o to 29.4 PSI) and 0 to 300Kpa (o to 44.1 PSI) available from stock. 0 to 45Kpa (o to 66.1 PSI) available on request.Single coil distributor, twin coil distributor or multicoil distributor-less ignition configurations are possible on most engines.Fitted with environmentally sealed connector the standard unit is splash proof. Units are available with double environmental sealing for use in the most arduous of applications (eg: - rally, off-road, and marine).Auxiliary output function that can be used for any of the following:Closed loop (feedback) boost pressure control for turbo charged engines with rpm and temperature dependent calibration characteristic.Closed loop (feedback) idle speed control.Control of engine cooling fan.Programmable on/off control for solenoid or relay driving that operates according to engine speed and load (eg: - can be used for gear shift control or light, over rev indicator, inlet camshaft timing selection or control of a supplementary electric fuel pump that augments mechanical fuel pump delivery at low engine rpm only).Fuel used pulse output to electronic or electro-mechanical counter with resolution of 0.1 litre (or use with trip computer).Or even more sophisticated control function such as servo control of auxiliary butterfly for turbo charged applications requiring precise throttle control and minimum turbo lag.Exhaust oxygen sensor input for sensing air/fuel ratio. Connect the low cost AUTRONIC 02 Sensor directly or for more demanding applications the AUTRONIC Wide Range Air/Fuel Ratio Sensor and Meter. The low cost sensor requires no interface adapters or expensive air/fuel ratio meters, and offers moderate accuracy and tolerance to leaded fuels. This function can be used to monitor air/fuel ratio during engine tuning or can be used for feedback control of air/fuel ratio for applications requiring exhaust catalytic conversion (feature available on request).Diagnostic/Error indicator of sensor or ECU fault conditions with memory for detection of intermittent fault conditions. An external light may also be connected for remote indication of abnormal operation.Precise spark advance control strategy for both static and dynamic operating conditions.Unique calibration strategy allows accurate control of fuel delivery under both acceleration and deceleration.User selectable spark and fuel delivery strategy for abnormal engine operation conditions to minimize possibility of engine damage whilst still maintaining engine operation. (eg: - over heated or over boosted).Comprehensive limp-home function with user selectable default settings that ensure engine operation can continue after sensor failure has occurred.Full compensation of engine control parameters for engine operation at any altitude (fuel delivery, ignition timing and boost pressure).Adaptive learning (with memory) to minimize the number of user setups required and to provide optimal control of air/fuel ratio, boost pressure and idle stability.Rev limiter with a soft characteristic that uses a combination of fuel delivery and spark control.Fuel pump safety shut-off. Pump stops 3 to 4 secs after the engine stops.Unit is ultra light weight/compact yet has sufficient drive capacity for high power continuous duty supplications. (One unit OK all applications from motor cycle to large capacity twin turbo engines).Optional interface unit to allow sequential operation without the need for separate crank/camshaft sensors or special multi-sensor distributor (P/N: - ADP102 available Q3-93).Remote monitoring of all functions using optional telemetry adapter (available Q2-93).INTERFACE REQUIREMENTS FOR MODEL SMCINPUTSSensorsIgnition input Hall effect. (Also available for direct connection to magnetic reluctor type pick-ups).No. 1 cylinder reference. (Also available for direct connection to magnetic reluctor type pick-ups).Barometric pressure (internal to ECU).Manifold pressure (internal to ECU).Throttle position.Intake air temperature.Engine coolant temperature.Exhaust oxygen (or optional Wide Range Air/Fuel Ration Sensor).AdjustmentsIdle mixture trim. (Internal to ECU and screwdriver adjustable from outside).OUTPUTSMain8 off injector driver (optional 2 injectors per driver).Ignition outputOpen collector output to any of the following:Single coil high-energy ignitions: Bosch 7 pin, Mitsubishi 3 pin.Autronic Capacitor Discharge Ignition.MSD 6A etc.4 outputs are available allowing multi coil distributor-less ignition for application on engines up to 8 cylinders.AuxiliaryFuel pump/injector fuel shut off safety relay.Multi function on-off or pulse width modulation output for either:Engine cooling fan relay.Idle speed actuator (variable duty cycle single pole type eg:- BoschTurbo charger waste gate control valve (SEM, most OEM types or AUTRONIC low or high capacity).Turbo charger auxiliary butterfly control motor.General-purpose duty cycle output with user defined characteristics.Fuel used pulse output (for trip computer function).SERIAL I/OCommunication with IBM compatible computer for calibration, fault diagnosis. (Some markets require special adapter).boost control, antilag, extra cylinder pulse, idle control 2 wire <a href="http://img406.imageshack.us/i/010w.jpg/" target="_blank"><img src="http://img406.imageshack.us/img406/6732/010w.th.jpg" border="0" class="linked-image" /></a> <a href="http://img268.imageshack.us/i/009sov.jpg/" target="_blank"><img src="http://img268.imageshack.us/img268/481/009sov.th.jpg" border="0" class="linked-image" /></a> <a href="http://img204.imageshack.us/i/011wcn.jpg/" target="_blank"><img src="http://img204.imageshack.us/img204/3654/011wcn.th.jpg" border="0" class="linked-image" /></a> $1100.00 paypal accepted, thanks matt Edited October 31, 2009 by monte383sbc Quote Link to comment Share on other sites More sharing options...
monte383sbc Posted October 31, 2009 Author Report Share Posted October 31, 2009 bump $1,100.00 shipped to your doors i promise you wont find a better deal and this system is aswsome Quote Link to comment Share on other sites More sharing options...
Starionboy84 Posted December 26, 2009 Report Share Posted December 26, 2009 interested, please pm me.. Quote Link to comment Share on other sites More sharing options...
eddiestarion Posted January 19, 2010 Report Share Posted January 19, 2010 interested, please pm me..hi i like to known if it still 4 sale plase call 631-220-9128 eddie Quote Link to comment Share on other sites More sharing options...
eddiestarion Posted January 19, 2010 Report Share Posted January 19, 2010 bump $1,100.00 shipped to your doors i promise you wont find a better deal and this system is aswsome is it still 4 sale ill pick it up today.give me a call 631-220 -9128 eddie thank u Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.