Jump to content



how to disassemble front seats for shipping

attn wrngwae

  • Please log in to reply
8 replies to this topic

#1 JohnnyWadd

JohnnyWadd

    Advanced Member

  • Banned
  • PipPipPipPip
  • 8,936 posts
  • Gender:Male
  • Location:Oregon
  • Model:Conquest

Posted 21 May 2012 - 03:34 PM

Here is how to get the front seat in a 18x18x32" box for shipping UPS fairly cheap. The whole idea of this was to get the dimensions of the individual components to the mininal.

Tools you need. The marker is to match mark stuff to help in reassembly..
Posted Image

Rails come off with four bolts...
Posted Image

Getting the plastic trim off use the screwdriver...and the exacto knife with some clear tape over the blade to prevent marring..
Posted Image
Posted Image
Posted Image
Posted Image
Posted Image

To sepearate the two halfs...
Hog rings pull off with pliers...frees up the flap that is held by the metal rod thing..
Posted Image
Posted Image
Also four 8 mm hex key bolt must come out..to free the main hinges..
Posted Image
But first...On the passenger seat is a cable with two 10mm nuts that adjust the free play, loosen those with the seat fully reclined backwards (more free cable) That will let you remove the "L" Shaped anchor. This part is best done right after you pull the trim parts off
Posted Image
Now you can also unbult the main hinges from the upper halfs..
Posted Image
Those bolts will have a panel covering them...so...look at the back of the upper seats there are two screws on the bottom of the panel..when you take those screws out the cover on the seat backs will slide downward and off...you will see this...
Posted Image
Now yo ucan use the 12 mm wrench and 10mm socket and undoe the headrest and the side peices and the under the knee peice. Some of those hog rings have to come off too and that will free up the flap.
Posted Image
Posted Image
Posted Image

Box carefully...
Posted Image

More pictures in my album.

Edited by JohnnyWadd, 21 May 2012 - 03:39 PM.






#2 wrngwae

wrngwae

    Always Smooth like Keith Stone

  • Vendors
  • PipPipPip
  • 3,447 posts
  • Gender:Male
  • Location:LaPorte, IN
  • Interests:trying to keep this motor under the hood, and off the engine stand
  • Model:Conquest

Posted 07 June 2012 - 01:23 PM

hey Johnny,,,,,,just got some time to put these back together........ it was a snap!!!! just some time and unwraping.......you were boared wernt ya lol.... everything arrived in good condition but i have one question what are all these extra nuts and bolts for ,,,,,,,,,, J/K...... but i do have 2 small springs for the life of me i cant figure out..........none of your pics show them. they are about 6" longish. any clue.
1989 Conquest  MOTOR BUILT BY DAD!!!!!!!!!.20 over block. Wiseco pistons.new M28 head w/ ss valves. Holeset Hx35 at 25psi.Snow Performance Meth injection, hurricane MPI intake manifold. 750 injectors. 3" exhaust. 3bar map sensor. Ajusta Head gasket. ARP head studs. FIP updated by Scott87star to control spark, and boost. running MS2.0.6. XTD stage 3 clutch.  I'm likely forgetting something. http://www.enginemachineservice.com http://www.starquestgarage.com
Scotts the man! check out his store.  http://www.starquest...             My site provided by Natallica the sticker Guru http://nbingaman.wix.../gntperformance Posted Image

#3 JohnnyWadd

JohnnyWadd

    Advanced Member

  • Banned
  • PipPipPipPip
  • 8,936 posts
  • Gender:Male
  • Location:Oregon
  • Model:Conquest

Posted 07 June 2012 - 04:26 PM

They go underneath http://s1187.photobu...05-17105650.jpg
I think that the picture....

#4 wrngwae

wrngwae

    Always Smooth like Keith Stone

  • Vendors
  • PipPipPip
  • 3,447 posts
  • Gender:Male
  • Location:LaPorte, IN
  • Interests:trying to keep this motor under the hood, and off the engine stand
  • Model:Conquest

Posted 08 June 2012 - 06:38 AM

yep,,,,,,,, found it... thanks Johnny!!! wife steam cleaned them last night.... turned out pretty good too. just hope they dont clash too bad with the black interior. wouldn't happen to have any other grey accessories? like a shifter boot i have been reading about lol....and others?
1989 Conquest  MOTOR BUILT BY DAD!!!!!!!!!.20 over block. Wiseco pistons.new M28 head w/ ss valves. Holeset Hx35 at 25psi.Snow Performance Meth injection, hurricane MPI intake manifold. 750 injectors. 3" exhaust. 3bar map sensor. Ajusta Head gasket. ARP head studs. FIP updated by Scott87star to control spark, and boost. running MS2.0.6. XTD stage 3 clutch.  I'm likely forgetting something. http://www.enginemachineservice.com http://www.starquestgarage.com
Scotts the man! check out his store.  http://www.starquest...             My site provided by Natallica the sticker Guru http://nbingaman.wix.../gntperformance Posted Image

#5 JohnnyWadd

JohnnyWadd

    Advanced Member

  • Banned
  • PipPipPipPip
  • 8,936 posts
  • Gender:Male
  • Location:Oregon
  • Model:Conquest

Posted 09 June 2012 - 11:42 PM

Shift boot that's all.

#6 wrngwae

wrngwae

    Always Smooth like Keith Stone

  • Vendors
  • PipPipPip
  • 3,447 posts
  • Gender:Male
  • Location:LaPorte, IN
  • Interests:trying to keep this motor under the hood, and off the engine stand
  • Model:Conquest

Posted 10 June 2012 - 09:01 AM

View PostJohnnyWadd, on 09 June 2012 - 11:42 PM, said:

Shift boot that's all.
talk to me.......
1989 Conquest  MOTOR BUILT BY DAD!!!!!!!!!.20 over block. Wiseco pistons.new M28 head w/ ss valves. Holeset Hx35 at 25psi.Snow Performance Meth injection, hurricane MPI intake manifold. 750 injectors. 3" exhaust. 3bar map sensor. Ajusta Head gasket. ARP head studs. FIP updated by Scott87star to control spark, and boost. running MS2.0.6. XTD stage 3 clutch.  I'm likely forgetting something. http://www.enginemachineservice.com http://www.starquestgarage.com
Scotts the man! check out his store.  http://www.starquest...             My site provided by Natallica the sticker Guru http://nbingaman.wix.../gntperformance Posted Image

#7 JohnnyWadd

JohnnyWadd

    Advanced Member

  • Banned
  • PipPipPipPip
  • 8,936 posts
  • Gender:Male
  • Location:Oregon
  • Model:Conquest

Posted 10 June 2012 - 03:28 PM

I'm waiting for it to come back I shipped it to a guy by mistake and he is sending it back.

#8 wrngwae

wrngwae

    Always Smooth like Keith Stone

  • Vendors
  • PipPipPip
  • 3,447 posts
  • Gender:Male
  • Location:LaPorte, IN
  • Interests:trying to keep this motor under the hood, and off the engine stand
  • Model:Conquest

Posted 10 June 2012 - 09:19 PM

lol,,,,,,,,,,,,,,,,,thats what you get for sooooo many threads,,,,,, J/K.... payment sent...

Edited by wrngwae, 10 June 2012 - 09:20 PM.

1989 Conquest  MOTOR BUILT BY DAD!!!!!!!!!.20 over block. Wiseco pistons.new M28 head w/ ss valves. Holeset Hx35 at 25psi.Snow Performance Meth injection, hurricane MPI intake manifold. 750 injectors. 3" exhaust. 3bar map sensor. Ajusta Head gasket. ARP head studs. FIP updated by Scott87star to control spark, and boost. running MS2.0.6. XTD stage 3 clutch.  I'm likely forgetting something. http://www.enginemachineservice.com http://www.starquestgarage.com
Scotts the man! check out his store.  http://www.starquest...             My site provided by Natallica the sticker Guru http://nbingaman.wix.../gntperformance Posted Image

#9 JohnnyWadd

JohnnyWadd

    Advanced Member

  • Banned
  • PipPipPipPip
  • 8,936 posts
  • Gender:Male
  • Location:Oregon
  • Model:Conquest

Posted 10 June 2012 - 10:22 PM

View Postwrngwae, on 10 June 2012 - 09:19 PM, said:

lol,,,,,,,,,,,,,,,,,thats what you get for sooooo many threads,,,,,, J/K.... payment sent...

good one haha




1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users