starquestJOE Posted April 14, 2009 Report Share Posted April 14, 2009 well since holset are hot right now on SQ's. I will show my set-up as well. I'm using a moded stock manifold from TEP. T3 w/out ex-waste gate HOLSET HX-40w. 18cm exhaust side. 4" in 4" out DODGE 4" downpipe for hx 40 the turbo sits in the stock location. very little is needed to put one on a SQ. Next i'll be working on the intercooler piping THIS ALL TEST FITMENTS ONLY http://i713.photobucket.com/albums/ww135/starquestJOE/P4130092.jpg http://i713.photobucket.com/albums/ww135/starquestJOE/P4130093.jpg http://i713.photobucket.com/albums/ww135/starquestJOE/P3150086.jpg http://i713.photobucket.com/albums/ww135/starquestJOE/P3150087.jpg http://i713.photobucket.com/albums/ww135/starquestJOE/P3150088.jpg http://i713.photobucket.com/albums/ww135/starquestJOE/P3150091.jpg Link to comment Share on other sites More sharing options...
rosengrant826 Posted April 14, 2009 Report Share Posted April 14, 2009 looks good, you going to run a 4" exhaust the whole way back ? Link to comment Share on other sites More sharing options...
starquestJOE Posted April 14, 2009 Author Report Share Posted April 14, 2009 No way it would never fit under the axle. alls i'm goin to get is one of those chrome stacks everyone has on there truck. and dump it out just in front of the pass rear wheel Link to comment Share on other sites More sharing options...
thagremlin Posted April 20, 2009 Report Share Posted April 20, 2009 ahh man whats with all these holsets poping up.. you guys planning on packing some serious power.. Link to comment Share on other sites More sharing options...
DieHARDmitsu. Posted May 2, 2009 Report Share Posted May 2, 2009 That is huge! A friend of mine has a 2g talon, 6 blot, 2.3 stroker, set up for track and uses the same HX-40 turbo. He runs well over 1000cc injectors and hits boost over 35psi...That Holset is no joke.... What do you plan to run for fuel? Link to comment Share on other sites More sharing options...
starquestJOE Posted May 3, 2009 Author Report Share Posted May 3, 2009 well i was thinking about tryin it with the TB and 2 1000cc inj. but i have JE block, P/P clearwater head adj rocker set up, adj cam gear, paxtom kamikaze fuel, pump, EIP cannon intake with 1000+ cc injectors, Electromotive Tec 2, fidanza flywheel, and more i'm hoping 450hp at around 26-28 psi Link to comment Share on other sites More sharing options...
NotStock88 Posted May 3, 2009 Report Share Posted May 3, 2009 well since holset are hot right now on SQ's. I will show my set-up as well. I'm using a moded stock manifold from TEP. T3 w/out ex-waste gate HOLSET HX-40w. 18cm exhaust side. 4" in 4" out DODGE 4" downpipe for hx 40 The stock exhaust manifold is not going to be able to flow enough air to spool that HUGE 18cm2 turbo. You will need a header at minimum for that turbo IMO. From what I have been reading about holsets, your best bet is to buy the bullseye performance turbine housing that they offer for DSM's and then just adapt the exhaust. Here is where I read up on it; http://www.dsmtuners.com/forums/turbo-syst...set-turbos.html Link to comment Share on other sites More sharing options...
starquestJOE Posted May 4, 2009 Author Report Share Posted May 4, 2009 i'm tryin to find the right housing for it but i havent had any luck Link to comment Share on other sites More sharing options...
thagremlin Posted June 14, 2009 Report Share Posted June 14, 2009 Best thing to do is get the specs on the turbine and talk to someone at bullseye and they should help you out. I was actually able to get factory specs from the maker of the turbo and just email them to bullseye and they hooked me up with the right housing that I need/looking for. Link to comment Share on other sites More sharing options...
GST95 Posted June 15, 2009 Report Share Posted June 15, 2009 i'm tryin to find the right housing for it but i havent had any luck What housing are you looking for? If you are looking for holset housings for it, the smallest direct fit housing for the hx40 that i know of is gunna be a 16cm. Another alternative would be to have a 12cm hx35 housing machined out for the hx40 turbine. If you want a BEP housing there are only 2 sizes, .55ar and .70ar. The .55 is mitsu flanged inlet and the .70 is t3 flanged inlet. They use to offer a .55ar t3 inlet, IIRC. Link to comment Share on other sites More sharing options...
starquestJOE Posted June 15, 2009 Author Report Share Posted June 15, 2009 i've been looking for any BEP housing. I have a T3 manifold and stock so. Link to comment Share on other sites More sharing options...
Scotty Dont Posted June 15, 2009 Report Share Posted June 15, 2009 http://www.timsturbos.com/SSTurbine_Housing_-_MHI_Inlet.html Link to comment Share on other sites More sharing options...
blue_crush Posted June 16, 2009 Report Share Posted June 16, 2009 hope everything works out good for ya. Link to comment Share on other sites More sharing options...
starquestJOE Posted June 16, 2009 Author Report Share Posted June 16, 2009 how do you like yours? Hows the spool time Link to comment Share on other sites More sharing options...
GST95 Posted June 16, 2009 Report Share Posted June 16, 2009 i've been looking for any BEP housing. I have a T3 manifold and stock so. BEP just did a run on the housings, so you shouldnt have a problem finding them. Link to comment Share on other sites More sharing options...
starquestJOE Posted June 25, 2009 Author Report Share Posted June 25, 2009 well as soon as i find some funds. Iwill be putting the holset on. the 12a just doesnt cut it anymore. i have alot of mods. but the 12a doesnt let me use them. i will run tbi first. i will be goin the same route as blue did with his. but a little different~~!!~~ Link to comment Share on other sites More sharing options...
Funky Phil Posted June 25, 2009 Report Share Posted June 25, 2009 The stock exhaust manifold is not going to be able to flow enough air to spool that HUGE 18cm2 turbo. You will need a header at minimum for that turbo IMO. From what I have been reading about holsets, your best bet is to buy the bullseye performance turbine housing that they offer for DSM's and then just adapt the exhaust. Here is where I read up on it; http://www.dsmtuners.com/forums/turbo-syst...set-turbos.html stock manifold is gonna flow whatever our heads let through. Link to comment Share on other sites More sharing options...
starquestJOE Posted June 25, 2009 Author Report Share Posted June 25, 2009 i have two heads. The one on the car is a tep stage 3. It came on the long block. And i have a P/P clearwater head with a mech setup. And both have cams. I also have the option to run A t3 or Stock mits housing on the turbo. I think i will be goin with the .70ar t3 BEP Link to comment Share on other sites More sharing options...
starquestJOE Posted February 7, 2010 Author Report Share Posted February 7, 2010 ok guys back from the dead! my BEP housing will be here tomorrow afternooon! I went with the .70ar t3 in, 3"v-band out. Also just got a AJUSA headgasket as well. So the set-up will be as follow:HX-40 in a 70ar BEP housingModded stock manifold T3 flangedTial 38mm ext wastse gateP/P clearwater haed with 1mm ov, hd spring, 274cam, mech setup, adj cam gearMAF-T and GM 3"mas I'll start posting pics as i start working on the car. I have alot of parts i bought from last year that never made it on the car as well Link to comment Share on other sites More sharing options...
starquestJOE Posted February 9, 2010 Author Report Share Posted February 9, 2010 http://i713.photobucket.com/albums/ww135/starquestJOE/Pic0287.jpghttp://i713.photobucket.com/albums/ww135/starquestJOE/Pic0289.jpghttp://i713.photobucket.com/albums/ww135/starquestJOE/Pic0290.jpg and next to a 20g housinghttp://i713.photobucket.com/albums/ww135/starquestJOE/Pic0288.jpg Link to comment Share on other sites More sharing options...
Funky Phil Posted February 9, 2010 Report Share Posted February 9, 2010 Are you gonna use the TEC for the tbi setup or stock computer??? Curious to see how the MAS will handle it since Ive seen a 14b max out a stocker. Good luck! Link to comment Share on other sites More sharing options...
starquestJOE Posted February 10, 2010 Author Report Share Posted February 10, 2010 stock computer on the tbi. but i have a MAF-T and gm 3"masw on the car now. i will move to blow threw after the turbo. right now its pull threw like a stock mas. also goin to run 2 big injectors if needed Link to comment Share on other sites More sharing options...
starquestJOE Posted February 10, 2010 Author Report Share Posted February 10, 2010 27x12x3 intercoolerhttp://i713.photobucket.com/albums/ww135/starquestJOE/Pic0294.jpg Link to comment Share on other sites More sharing options...
Funky Phil Posted February 10, 2010 Report Share Posted February 10, 2010 Best of luck, thats quite a large turbine. Link to comment Share on other sites More sharing options...
substock Posted February 10, 2010 Report Share Posted February 10, 2010 no more plans of going mpi?good luck with the blow thru setup, thats a huge turbo Link to comment Share on other sites More sharing options...
Recommended Posts