Jump to content

1989 TSI - orig owner 18 years - sat for the last 8 - coming


ptracy26
 Share

Recommended Posts

coming out party soon! can't wait (another month or so)

 

http://www.skarproductions.com/conquest/front.jpg

http://www.skarproductions.com/conquest/side.jpg

http://www.skarproductions.com/conquest/wheel.jpg

http://www.skarproductions.com/conquest/wheel2.jpg

Link to comment
Share on other sites

Your correct my friend - this pic was last taken before the bshop work. Looks like they didn't want to cover my engine bay. (nice n dirty now - I'll get it back to that +more)

 

http://www.skarproductions.com/conquest/2361.JPG

Link to comment
Share on other sites

  • 6 months later...

Oh boy, its been a year but the car is finally shipped to FL. from CT. now sitting comfortably. Just awaiting the air damn from 101 and its back in business.

 

http://skarproductions.com/conquest/TSI_Dside.jpg

http://skarproductions.com/conquest/TSI_Fside.jpg

http://skarproductions.com/conquest/TSI_side.jpg

http://skarproductions.com/conquest/TSI_rearpanel.jpg

http://skarproductions.com/conquest/TSI_inside.jpg

Towing vehicle - not(couldn't help myself)

http://skarproductions.com/conquest/Jeep.jpg

Edited by ptracy26
Link to comment
Share on other sites

  • 9 months later...

Added the splitter & front airdam, figure finish the post - out

http://www.skarproductions.com/Conquest/sidesplitter.jpg

http://www.skarproductions.com/Conquest/Frontsplitter.jpg

http://www.skarproductions.com/Conquest/Fullefts.jpg

http://www.skarproductions.com/Conquest/leftsideh.jpg

http://www.skarproductions.com/Conquest/Fullrights.jpg

http://www.skarproductions.com/Conquest/Farawayr.jpg

http://www.skarproductions.com/Conquest/open_rside.jpg

http://www.skarproductions.com/Conquest/1stfront2.jpg

http://www.skarproductions.com/Conquest/1stpart.jpg

http://www.skarproductions.com/Conquest/nigths1.jpg

Link to comment
Share on other sites

Sure, I purchased this off of eBay about 2 years ago but I understand that a member her made them. They are two piece design made of bullet proof plastic(?) though I think is lexan. He provides all the mouting info related to the air splitter to spoiler.

 

I took it a slight step futher by adding door trim to the outside of the splitter as well as adding splitter connecting rods. The door/weather stipping ($3) looks nice actualy which the pics don't justify. The connecting rods I used JB weld to secure underneath the front bumper to a sheet of metal (just the nut is secured so you can unscrew the rod still) and attached for support to below as shown in the pics.

 

There where pics on the site here of other users who had this same setup, though haven't seen them at all since (don't know if that's good news). I'll check my email to see if there was some correspondence.

 

pt26 - back at Indy 500 yahoooooo!

Link to comment
Share on other sites

same, same to you( I agree).

 

I kept it as clean as I could, though 9,900.00 (that's also with a 100.00 gift cert. from friends lol) later for rust removal, refab panels and new paint etc... got it back to what you see at now. burp - ugh - I always get ready to hurl when I mention that.

Edited by ptracy26
Link to comment
Share on other sites

  • 2 months later...
  • 2 weeks later...
  • 2 weeks later...
Is that intake still available? Looks sweeet and functional

 

 

Yes it is, its stock. The addons where 101's FPR (which I just bent his adapter plate that comes with it and drilled a hole in it, shared the secured connector with the dipstick), Trilogy injectors, and Lower Shores performace custom steel braided lines I ordered. Thats if your talking about the TB

 

If its the intake to the turbo, that's an hks compressor bypass setup (yeah that may be a tough find, geesh bought that 17 years ago) with Cosmo Racing air filter(ebay - recent).

 

 

 

pt26

Link to comment
Share on other sites

Yes it is, its stock. The addons where 101's FPR (which I just bent his adapter plate that comes with it and drilled a hole in it, shared the secured connector with the dipstick), Trilogy injectors, and Lower Shores performace custom steel braided lines I ordered. Thats if your talking about the TB

 

If its the intake to the turbo, that's an hks compressor bypass setup (yeah that may be a tough find, geesh bought that 17 years ago) with Cosmo Racing air filter(ebay - recent).

 

 

 

pt26

Very clean ride. Reminds me of MitsuMark's old car.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
 Share

×
×
  • Create New...