allen405 Posted May 11, 2012 Report Share Posted May 11, 2012 How can you tell if it's working or not? Link to comment Share on other sites More sharing options...
scott87star Posted May 11, 2012 Report Share Posted May 11, 2012 If the ECU is throwing the trouble code for the O2 when the engine is fully warmed up then its not. Link to comment Share on other sites More sharing options...
allen405 Posted May 11, 2012 Author Report Share Posted May 11, 2012 Ok, thanks. Next question what is the shielding for on the wire that goes all the way into the cab? because some of mine is missing Link to comment Share on other sites More sharing options...
alp247 Posted May 11, 2012 Report Share Posted May 11, 2012 allen405, Yeah if you can pull the codes you'll know. I mean i check mine every morning when i start it since i have a led hooked up. I check it down the road later and when the light is on and not blinking (single blink)...well then i know it's working. If it hasn't stop blinking then i know i need to replace it. If you havne't hooked up a light to where you pull the codes i recommend it. Saves you time and you can check for any code that shows up. Link to comment Share on other sites More sharing options...
DMNDSTAR87 Posted May 11, 2012 Report Share Posted May 11, 2012 (edited) Ok, thanks. Next question what is the shielding for on the wire that goes all the way into the cab? because some of mine is missingthe sheilding keeps out any electrical interference from disturbing the 02 signal to the ECU.U will always pull an 02 code upon startup and once exhaust gets up to temp it will stop pulling the code if ur sensor is good.I tapped of the harness in the glove box and ran a LED and mounted it my dash.That way u can watch the blinks and know whats happening with more than just the 02 sensor.Very simple to do and cheap also--gig out Edited May 11, 2012 by DMNDSTAR87 Link to comment Share on other sites More sharing options...
allen405 Posted May 12, 2012 Author Report Share Posted May 12, 2012 Where do I get a led light with wires on it and how do I hook it up? Link to comment Share on other sites More sharing options...
DMNDSTAR87 Posted May 13, 2012 Report Share Posted May 13, 2012 (edited) Where do I get a led light with wires on it and how do I hook it up?I had an led kickin' around from a car alarm but did need a resistor(positive side) cause a car alarm led is only rated for like 5 volts---Go see ur local stereo/alarm install guy he probably has a drawer full of unused leds and resistors(ask me how i know )---87 FSM SEC.14-61 14-62. Pull down glovebox--locate the unhooked plug--looking at plug top right wire is the positive(blk-red tracer)bottom left is negative(blk wire)If u do this I highly reccomend soldering where u tap in at the glovebox----here is a pic where I have my wideband and ecu diagnostic leds mounted This will allow u to moniter ur O2,SPEED SENSOR,AIRFLOW SENSOR,TPS,ISC/MPS AND COOLANT TEMP SENSOR.Just because u r pulling one of these code does not insure u of a bad part so use the led for a reference to troubleshoot(do not just replace something cause its giving u a code).just to be sure of urself open up the manual and its pretty self explanatory---good luckgig outhttp://i1125.photobucket.com/albums/l587/dmndstar87/DSC00817.jpg Edited May 13, 2012 by DMNDSTAR87 Link to comment Share on other sites More sharing options...
toofast Posted May 13, 2012 Report Share Posted May 13, 2012 Where do I get a led light with wires on it and how do I hook it up?You can get one at radio shack here is the link http://www.radioshack.com/product/index.jsp?productId=2062548 Link to comment Share on other sites More sharing options...
allen405 Posted May 14, 2012 Author Report Share Posted May 14, 2012 Thanks, I picked one up at advance auto. Link to comment Share on other sites More sharing options...
Recommended Posts