Jump to content



Does oil cooler lines have washer at filter adapter?


  • Please log in to reply
4 replies to this topic

#1 Preludedude

Preludedude

    Established Member

  • Members
  • PipPipPip
  • 2,745 posts
  • Gender:Male
  • Location:Upstate, SC
  • Model:Conquest

Posted 03 September 2018 - 05:17 PM

I know the oil cooler lines have a rubber/copper washer (MB033054) at the cooler.  

BUT

Do the cooler lines use the same washer where the lines connect to the filter sandwich adapter?

Edited by Preludedude, 03 September 2018 - 05:17 PM.






#2 speedyquest

speedyquest

    Established Member

  • Members
  • PipPipPip
  • 3,987 posts
  • Gender:Male
  • Location:La Crosse Wisconsin
  • Interests:bmx, cars, computers
  • Model:Starion

Posted 03 September 2018 - 05:23 PM

I believe so yes. Ironically I'm tearing all of that out of my car today and installing a mishimoto oil cooler kit. And.... I've ran into a snag that will require some modification of the original sandwich plate bolt.

1987 Flatty Starion -- Widebody Conversion -- V-Mount Setup --  JDL Tubular Manifold  --  MX-6 Intake -- MS3-Pro -- AEM FPR  --  ARP head studs -- 3" hood exit exhaust -- Hahn Racecraft 16g --  Tial F38 Wastegate -- Tial Q Bov -- Short route piping -- 5 lug & LSD conversion -- Tubular Front End -- Manual Steering Rack Conversion -- Manual Brake Conversion -- Stack Digital Dash -- AEM UEGO -- D2 coilovers -- full GNT poly bushings & mounts -- four 8" rears -- car lightened significantly...  More to come!


Posted Image


Build Thread --->  http://www.starquest...opic=143564&hl=


#3 Dad

Dad

    Advanced Member

  • Vendors
  • PipPipPipPip
  • 8,130 posts
  • Gender:Male
  • Location:Niles,Ohio
  • Interests:One stock and one not!
    87 White Quest
    87 Shetland
    83 Starion- Chevy powered
    ___________________________
  • Model:Conquest

Posted 03 September 2018 - 08:11 PM

Same washers at cooler and filter adapter.

#4 TexasQuest

TexasQuest

    Advanced Member

  • Members
  • PipPipPipPip
  • 8,755 posts
  • Gender:Male
  • Location:Sunnyvale, Texas
  • Interests:TSi's & VR4's
  • Model:Conquest

Posted 03 September 2018 - 10:13 PM

Mitsubishi is pretty good about using the same hardware for multiple parts on the car.
88 Fiji Blue -Tsi
Zoom clutch, Fidanza flywheel, Stedebani shifter, KSport coilovers, ST swaybars, abs delete, a/c delete, cruise delete, JVE, BSEK, TEP steel brake lines, LSP braided cooler lines, CX Racing radiator,  MK1 silicone hoses, MK1 pullies, *DM hard pipes & intercooler,14G turbo, ported exh. manifold, MAF Translator, 3.5" GM maf, Turbo XS RFL bov, *DM 3" exhaust, Cusco front strut bar, TEP rear strut bar, Enkei 92's, HKS turbo timer, AEM wideband, AEM boost gauge, AEM oil pressure gauge, Hallman boost controller
Posted Image

View PostJohnnyWadd, on 04 March 2010 - 10:01 PM, said:

my shaft was big i dont know what your talking about.

#5 importwarrior

importwarrior

    6 Quests and Counting......

  • Moderators
  • PipPipPipPipPip
  • 18,156 posts
  • Gender:Male
  • Location:Manassas VA
  • Interests:Boost = 2KWIK4U
    Starquests
  • Model:Conquest

Posted 04 September 2018 - 04:38 PM

Yup if banjo bolts then 2 copper crush washers each bolt.

Bolt
Copper crush washer
Banjo -hose
Copper crush washer
Bolt it in

B-71 87 TSI ~ RIP

Black 87 Starion ~ Mess SOLD!!!

Proud New 89 slightly Rusted Fiji Owner !!!







0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users