Jump to content

Kenny G

Members
  • Posts

    198
  • Joined

  • Last visited

About Kenny G

  • Birthday 08/20/1961

Contact Methods

  • Skype
    kennygpcguru
  • ICQ
    0
  • Website URL
    http://kennethgraham2@cox.net

Profile Information

  • Interests
    Keeping my 87 Conquest and 83 280ZX turbo on the road is a 24 hour job, but I love it! I love to see the finished product when you brought it back from the junk yard knowing you revived it with your own 2 hands.
  • Location
    Hampton, VA
  • Gender
    Male

Previous Fields

  • Zip Code
    23669
  • Model
    Conquest
  • Type
    TSI
  • Model Year
    1987
  • Transmission Type
    Manual
  • Factory Color
    California Red
  • Interior Color
    Black
  • Status
    On the road

Kenny G's Achievements

Newbie

Newbie (1/14)

1

Reputation

  1. check your fusible links and grounds. also check/swap your ECI control relay under the right kick panel above the ECU.
  2. my problem was with the knock box on my 87. I just upgraded it with an 88 ignition box, just kept the connector and wired it up. works great!
  3. text me at 7572910157 im about to scape my parts car. send a pic of what you need
  4. I have a parts car that's an 88, I'm sure this is what you need but I also had an 87 an don't know if they are interchangeable. not sure on the part numbers that I have.
  5. yes, I know they are very hard to find. is the caliper different on an 87? do you know the part number? lmk text me at 757-291-0157
  6. I have some but need work with clear coat. text me at 757-291-0157 for pics. cheap $35 each plus shipping.
  7. I have one ready to go. text me the picture to verify the part. I that's it I will sell for $10 to you plus shipping.
  8. my 87 knock box died and left me stranded. hard to find a 87 and below, but I was told to get about 6" from a harness of 88-89 igniter box and use that box instead as they more reliable. I did and just left off the 2 extra wires off, all others are color coded the same and it fired right up! Good luck finding one. I got a broke one if you want it!
  9. I think I have a set when I pull the bumper off my parts car. I will see if I can locate them. PM me if your interested
  10. Don't forget to replace your foam seals before install your tail lights, this will prevent water infiltration thus prevent the corrosion in the future. Make them from 1/4" foam using the old ones as a pattern. I'm still looking for the sockets then I can text or email pics to you. PM your info to me and ill do it this weekend.
  11. I have them both let me put my hands on them and I'll let you know. Pm me by the weekend if you don't hear from me if you still need them.
  12. Kenny G

    Badges

    I got a set last year, I still have some and the box it shipped in. I will check when I get home and let you know who I got them from.
  13. Kenny G

    radio

    Have you tried replacing the drive belts on yours yet? very hard to find one that works after 25 years. I did mine and it works fine now.
  14. the shield looks like a round drink cup on the end of you trans. if your drive shaft is installed on the trans, you will see part of the input shaft from your u joint end (if your shield is NOT installed). If you can't see the shaft and the shield will cover it up to the u joint. I hope this helps.
  15. while on jacks, check to make sure your forward drive shaft u joint in not rubbing on the back of your transmission output shaft shield. it will make a very loud grinding sound. I found mine out of round and could not straighten it so I just removed it from the back of the tranny. it's only pressed on the end and can easily be removed. good searching!
×
×
  • Create New...