Jump to content



Stand alone knock sensor


  • Please log in to reply
3 replies to this topic

#1 03CL55AMG

03CL55AMG

    Established Member

  • Members
  • PipPipPip
  • 576 posts
  • Gender:Male
  • Location:Pensacola FL
  • Interests:cars and more cars, and hot girls
  • Model:Conquest

Posted 10 April 2018 - 12:31 PM

So where is the stock knock sensor on a conquest, and if I needed to put one in for a standalone where would it be located.
Forged motor, weisco pistons ,3" exhaust, garret 60 cold/ 96 hot turbo, 950/ 1800 injectors , 52mm tb, maft, meth kit.





#2 speedyquest

speedyquest

    Established Member

  • Members
  • PipPipPip
  • 3,890 posts
  • Gender:Male
  • Location:La Crosse Wisconsin
  • Interests:bmx, cars, computers
  • Model:Starion

Posted 10 April 2018 - 12:42 PM

The stock sensor threads into a blind hole near the oil filter sandwich on the block.

1987 Flatty Starion -- Widebody Conversion -- V-Mount Setup --  JDL Tubular Manifold  --  MX-6 Intake -- MS3-Pro -- AEM FPR  --  ARP head studs -- 3" hood exit exhaust -- Hahn Racecraft 16g --  Tial F38 Wastegate -- Tial Q Bov -- Short route piping -- 5 lug & LSD conversion -- Tubular Front End -- Manual Steering Rack Conversion -- Manual Brake Conversion -- Stack Digital Dash -- AEM UEGO -- D2 coilovers -- full GNT poly bushings & mounts -- four 8" rears -- car lightened significantly...  More to come!


Posted Image


Build Thread --->  http://www.starquest...opic=143564&hl=


#3 03CL55AMG

03CL55AMG

    Established Member

  • Members
  • PipPipPip
  • 576 posts
  • Gender:Male
  • Location:Pensacola FL
  • Interests:cars and more cars, and hot girls
  • Model:Conquest

Posted 10 April 2018 - 09:42 PM

Thanks speedy.
Forged motor, weisco pistons ,3" exhaust, garret 60 cold/ 96 hot turbo, 950/ 1800 injectors , 52mm tb, maft, meth kit.

#4 mstieg

mstieg

    Advanced Member

  • Members
  • PipPipPipPip
  • 6,171 posts
  • Gender:Male
  • Location:Fort Myers, FL
  • Model:Starion

Posted 11 April 2018 - 12:09 AM

http://www.starquest...howtopic=134679

and

http://www.starquest...opic=145242&hl=
Before: 352 rwhp @15psi; MPI: SDS EM5F; Chad intake & equal length header; S256 turbo (56/80comp-64/74ex); 48" of 2.5" IC piping
Now Done:  7.5:1 .35 Wiseco rebuild w/ crank scraper; 274 Magna roller cam & 1.55 rockers; mod port AMC head; 1mm>valves; Innovate WB; GM alt/rewired; 3" 240 alum radiator, elec fans; BMW X5 oil separator exh. crankcase vent; gas tank renewed; D2s; sway/strut bars; LT1 T56 clutch & trans swap w/ Fidanza; 4.22 rear; 265 Kumos on SHP rears; new steering pump/box/lines & coupler fix: http://www.starquest...howtopic=139558; full dash/console rewire - Autometer, push start, etc.
In Progress: breakin & tune
Future: Enjoy driving again; meets & local shows; AC; WG reroute from open vent to exh; Water/Meth?; body/paint

FOR SALE:  Rear Camber plates (basic); NIB beefy U-joints(2); etc.see-->  http://www.starquest...howtopic=133262 Custom 5 gauge overlay panel: http://www.starquest...pic=136703&st=0




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users