Jump to content

wolvorine4

Members
  • Posts

    21
  • Joined

  • Last visited

Profile Information

  • Interests
    I love Ya Quest
  • Location
    Philadelphia, PA

Contact Methods

  • ICQ
    39552001

wolvorine4's Achievements

Newbie

Newbie (1/14)

0

Reputation

  1. Its a rebuild Block with: 40 over Wiseco 8:1 Pistons w/ total seal rings ARP Main and Rod Bolts Clevel77 Bearings Main and Rods Block was Cleaned and Mains where Line honed (I believe that is what it is called) Rods preped and small end bushed for floter pins Full motor Balanced and Blue Printed BS full eliminator kit w/ timing components High Volume Oil Pump Freeze Plugs 5+k in parts and labor, I'm not looking to rip anyone off. Make a resonable offer and its yours. I will post pictures on my website by tomorrow. Will post link when Pics are up. If anyone has any requests in a specific picture let me know. Also, I have a TON of other parts And I will throw in the CAR too for FREE if you get the Block... The currently engine in the car does run but knocks like a B***H. Not Drivable. So you will need a TowTruck. If no one wants the car, I will JunkYard it. I can only hold the car for about 1 to 1 1/2 weeks... I need the room. If you have questions, Email me: wolvorine4424@gmail.com or Call: (267)984-3648. Or you can just post questions here. Roman EDIT: Sorry, Forgot to mention. I'm Located in Philadelphia, PA.
  2. Is someone still working on this or what??? I'm interested... Did everyone quit... I do not want to do it myself, but if i have to i will get down and durty w/ the fiberglass and reisin, etc. The molding is a pain in the a&&
  3. Is this kit coming out or what... I would love a set of lambo doors... I dont see them to much here... Maybe 1 a month (there is only about 4 cars here with lambo doors... $350 I'm in... let me know whats going on with it
  4. Just my .02c. I prefer the turbo facing the front... Less headaches on exhaust piping and intake piping... Did you have to mod the crossmember to install the motor... or did you just made brackets from the stock mounts to motor block...
  5. That looks awsome..... What are the power output on this baby... What was the total Price for this swap including everything... Can you give me a rough astimate in g's. (ex. 5000 to 6000)..... Looks great... i want to see it... I will take my quest down also...
  6. i cant program it yet.. :'(. i just want a working file so i can see how the timing, fuel curves are for this motor... i will NOT use someone elses bin file on my new engine... its just for learning... ??? My new motor/ign. sys. will be proffesionaly set and dyno... ;D ;D ;D
  7. no, not yet... the unit will only be installed in about 2 weeks... i want to get the program working
  8. tec3 has alot more paramaters that you can configure, that tec2 did not have... ok, here is there i get stuck on: 1. engine advance table... 2. inj. pulse timing well, this is good, if you know the programs... but till then its a pain in the a$$.
  9. BIN file needed, Please... WinTec3 v3.1.1 (programing software) wt301t3.EM3 (upgrade to tec3 filmware)
  10. Can someone email me the program file for wintec 3, i want to get to know the settings... tec3 is not in the car yet... but in about a month it will be installed... I already have wintec v3.1.1... just need the bin file... Thank you, Roman wolvorine4@comcast.net
  11. About step 4: My starion hit .88 volts... That is very close to the .9 that it needed... If you get a lower or higher voltage (not sure if up or down volt) you may not have the engine warmed up all the way or you have a temp sensor problem.
  12. good luck I will just get a sunroof in the car, i'm not a fan of convertibles ( hard top is ok ) Would you be able to give the the phone number and the address of the place that did the custom bumper for you, If you have it? Thank you, Roman
  13. i'm getting in on this one... Looks HOT ;D What about the rear bumper, i would like it to be a little lower ( maybe 2 to 3 inches )... do you think thats posible?
  14. I tried the mitsu dealer and they told me that they cant get it... Is there an alternative???
×
×
  • Create New...