NikoFab's 1986 Starion ESI-R
Posted 18 May 2012 - 09:00 PM
Rear speaker panels
Posted 18 May 2012 - 09:49 PM
Rear shoulder bolsters and lower rear sails
Posted 18 May 2012 - 09:55 PM
Driver's side door panel. I got these panels off of an '88 with automatic seatbelts. This was perfect since I'm switching to Corbeau seats with 4-point harnesses, and the '88 panels don't have the hole for the manual seatbelts, which are being removed entirely. Door handle surround still needs to be touched up and installed.
Posted 18 May 2012 - 09:55 PM
Like this MB 500 SL at the Philadelphia Auto show.
Posted 18 May 2012 - 10:01 PM
Another modification is for the triangular panel to the rear of the door. The one from my '86 manual seatbelt setup hangs on a dual hanger (you can see the two holes where that hanger was mounted). The one from the '88 screws into two brackets which I don't have. Going to see what I can fabricate to get it to work...maybe create a flange that mounts to the holes that the the hanger used to mount on.
Posted 18 May 2012 - 10:04 PM
Posted 22 May 2012 - 03:11 PM
Posted 22 May 2012 - 03:55 PM
Posted 24 May 2012 - 06:34 PM
Got the passenger side done today. Also managed to address the triangle piece mounting issue by creating my own flanges and threading them so the triangles are secured. Not bad if I say so myself.
Posted 19 June 2012 - 05:04 PM
Got the smoked fog light covers from Tim at MotoCam360 today...they look pretty sharp I think. Still have to install the LED fog lights I got from 87quest_stv. I'll get pics of that install up as soon as possible.
Posted 19 June 2012 - 05:20 PM
Posted 19 June 2012 - 05:22 PM
Posted 21 June 2012 - 07:56 PM
Ok some interior work done. Got all my new upholstery in this week and got started installing in the back of the car. Looks pretty good I think. Can't do the front upholstery until I install my new seats which also came in this week. Going to have to fabricate some adapter rails so that the new seat rails will bolt to the stock floor mounts. Anyway here's some pics of the rear upholstery going in.
Edited by Nikolaya, 21 June 2012 - 08:02 PM.
Posted 22 June 2012 - 01:50 AM
Posted 22 June 2012 - 02:17 AM
yes it's been a lot of work but it will certainly be worth it in the long run. as soon as i get things a bit more organized, i'll start cleaning parts and posting them for sale...i'm sure there's people who can use them.
Posted 22 June 2012 - 04:34 PM
Zoom clutch, Fidanza flywheel, Stedebani shifter, KSport coilovers, ST swaybars, abs delete, a/c delete, cruise delete, JVE, BSEK, TEP steel brake lines, LSP braided cooler lines, CX Racing radiator, MK1 silicone hoses, MK1 pullies, *DM hard pipes & intercooler,14G turbo, ported exh. manifold, MAF Translator, 3.5" GM maf, Turbo XS RFL bov, *DM 3" exhaust, Cusco front strut bar, TEP rear strut bar, Enkei 92's, HKS turbo timer, AEM wideband, AEM boost gauge, AEM oil pressure gauge, SPA fuel regulator, Hallman boost controller
<SQ Garage> http://www.starquestgarage.com/
Posted 22 June 2012 - 07:07 PM
Posted 25 June 2012 - 07:13 AM
I got my front and rear strut brace sets from ESIrType? the other day...very nice pieces of hardware. Went ahead and installed the rears since the upholstery was already in and ready to go. Looks pretty good!
Edited by Nikolaya, 25 June 2012 - 07:13 AM.
Posted 25 June 2012 - 08:47 PM
1989 Conquest tsi fiji: on the road
1988 Palermo grey: on the road
1988 Conquest tsi fiji: in storage for sale
Posted 25 June 2012 - 09:10 PM
1 user(s) are reading this topic
0 members, 1 guests, 0 anonymous users